Toyota Corolla 2008 Owner'S Manual Download Page 190

Page: 190 / 310

’08 Corolla_U (L/O 0706)

102

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

If the indicator or buzzer comes on...

Do this.

(a)

If parking brake is off, stop immediately and contact Toyota dealer.

(b)

(indicator and buzzer)

Fasten driver’s seat belt.

(c)

(indicator and buzzer)

Fasten front passenger’s seat belt.

(d)

Stop immediately and contact Toyota dealer.

(e)

Take vehicle to Toyota dealer.

(f)

Fill up tank.

(g)

Stop and check.

Service reminder indicators and warning buzzers

Summary of Contents for Corolla 2008























































































































































































































































































































Search results

Summary of Contents for Corolla 2008

Reviews:

Related manuals for Corolla 2008

Brands by name

Popular brands

Toyota Corolla 2008, Owner'S Manual

Search results

Summary of Contents for Corolla 2008

Reviews:

Related manuals for Corolla 2008

Brands by name

Popular brands