Toyota Corolla 2008 Owner'S Manual Download Page 114 | Manualshive

Page: 114 / 310

background image

’08 Corolla_U (L/O 0706)

26

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

4. Lock all the doors with the key or wire-

less remote control transmitter. At this
time, the TVIP indicator light comes
on.

The system will be set in 30 seconds.
When the system is set, the indicator
light will start to flashing again.

5. Make sure that the indicator light

flashes. Then you may leave the ve-
hicle.

Never leave anyone in the vehicle when
you set the system because unlocking
from the inside activates the alarm.

Activating the alarm

If the system detects a threat to the
vehicle, it sounds the alarm for one
minute while flashing headlights and
turn signal lights.

At this time, the interior light also turns
on when the interior light switch is in the
“DOOR” position. (See “Interior light” on
page 93 in Section 1−5.)

The system detects a threat under any of
the following conditions:

Either of the front doors is unlocked by
means other than the key or wireless
remote control transmitter.

If the key is not in the ignition switch,
all the doors will be automatically
locked again.

Any of the doors or trunk lid are forci-
bly opened.

The alarm will activate when the trunk
lid is opened with a key. Cancel the
system before opening the trunk lid.

The side windows are tapped or bro-
ken.

The battery terminal is disconnected
and then reconnected.

The ignition is hotwired.

After one minute, the alarm automatically
stops and the indicator light starts flashing
again.

Reactivating the alarm

Once set, until you cancel the system, the
system automatically resets the alarm af-
ter the alarm has stopped.

The alarm will activate again under the
same circumstances described in “Activat-
ing the alarm”.

Stopping the alarm

You can stop the alarm in either of the
following ways:

Unlock any of the doors with the key
or wireless remote control transmitter.

Place the ignition switch in the “ON”
position.

CANCELLING THE SYSTEM

You can cancel the system as described
in “Stopping the alarm”.

If you cancel the system by unlocking any
of the doors but no door is opened within
30 seconds, all the doors lock automati-
cally and the system will be set again.

«
...
112
113
114
115
116
...
»

Summary of Contents for Corolla 2008























































































































































































































































































































Reviews:

No comments

Related manuals for Corolla 2008

Brand: Federal Signal Corporation Pages: 13

Brand: IAME Pages: 17

Brand: Yakima Pages: 8

Brand: Carcomm Pages: 2

Brand: Whispbar Pages: 14

Brand: Buick Pages: 428

Brand: Axxess Pages: 8

Brand: Mercedes-Benz Pages: 373

Brand: Chevrolet Pages: 2

Brand: XTC Pages: 4

OCTAVIA - TECHNICAL CHANGES 11-2009

Brand: Skoda Pages: 16

Brand: DriveRight Pages: 16

Brand: Whispbar Pages: 14

Brand: Curt Group Pages: 2

Brand: Toyota Pages: 204

Brand: Honda Pages: 5

Brand: Valueline Pages: 40

Brand: Blackhawk Automotive Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands