Toyota Corolla 2008 Owner'S Manual Download Page 193 | Manualshive

Page: 193 / 310

background image

’08 Corolla_U (L/O 0706)

105

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

(a) Brake System Warning Light

This light comes on in the following cases
when the ignition key is in the “ON” posi-
tion.

When the parking brake is applied...

Vehicles with anti−lock brake system—

This light comes on for a few seconds
when the ignition key is turned to the
“ON” position even after the parking brake
is released.

When the brake fluid level is low...

CAUTION

It is dangerous to continue driving
normally when the brake fluid level is
low.

Have your vehicle checked at your
Toyota dealer in the following cases:

The light does not come on even if the
parking brake is applied when the igni-
tion key is in the “ON” position.

Vehicles with anti−lock brake system—

The light does not come on even if the
ignition key is turned on with the park-
ing brake released.

A warning light turning on briefly during
operation does not indicate a problem.

CAUTION

If either of the following conditions
occurs, immediately stop your vehicle
at a safe place and contact your
Toyota dealer.

The light does not turn off even
after the parking brake is released
while the engine is running.

In this case, the brakes may not
work properly and your stopping
distance will become longer. De-
press the brake pedal firmly and
bring the vehicle to an immediate
stop.

Vehicles with anti−lock brake sys-
tem—

The brake system warning light re-
mains on together with the “ABS”
warning light.

In this case, not only the anti−lock
brake system will fail but also the
vehicle will become extremely un-
stable during braking.

(b) Driver’s Seat Belt Reminder Light

and Buzzer

The light and buzzer act as a reminder to
buckle up the driver’s seat belt.

Once the ignition key is turned to “ON” or
“START”, the reminder light flashes and
buzzer sounds if the driver’s seat belt is
not fastened. Unless the driver fastens the
belt, the light keeps flashing and the
buzzer stops after about 6 seconds.

If the vehicle speed rises above 15 km/h
(9 mph) with the seat belt unfastened, the
buzzer will sound for about 10 seconds.
Then, if the seat belt is still unfastened,
the buzzer will sound in a different tone
for 20 seconds. Even if the vehicle speed
drops below 15 km/h (9 mph), the buzzer
will continue to sound. To stop the buzzer,
fasten the seat belt. If the buzzer still
sounds, make sure the front passenger’s
seat belt is fastened.

«
...
191
192
193
194
195
...
»

Summary of Contents for Corolla 2008























































































































































































































































































































Reviews:

No comments

Related manuals for Corolla 2008

Brand: Saab Pages: 75

Brand: RAM Pages: 20

Retrotech RTX-68D-CHG

Brand: Dakota Digital Pages: 4

Brand: Mercedes-Benz Pages: 373

1973 Convertible

Brand: Volkswagen Pages: 80

Brand: Actia Pages: 102

Brand: Cadillac Pages: 368

Brand: Luverne Pages: 3

Brand: Navman Pages: 27

Brand: Whispbar Pages: 14

Brand: Thule Pages: 8

Brand: Easee Pages: 12

RGBW Rock Lights

Brand: Lit Lightz Pages: 3

Brand: v.LOGiC Pages: 22

Brand: TOPPOINT Pages: 2

LED Dominator TAM83S2

Brand: Whelen Engineering Company Pages: 2

Brand: Whispbar Pages: 14

Brand: ZENEC Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands