Toyota Corolla 2008 Owner'S Manual Download Page 70 | Manualshive

Page: 70 / 310

background image

’08 Corolla_U (L/O 0706)

244

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

Carpets

Use a good foam−type shampoo to
clean the carpets.

Begin by vacuuming thoroughly to remove
as much dirt as possible. Several types of
foam cleaners are available; some are in
aerosol cans and others are powders or
liquids which you mix with water to pro-
duce a foam. To shampoo the carpets,
use a sponge or brush to apply the foam.
Rub in overlapping circles.

Do not apply water—the best results are
obtained by keeping the carpet as dry as
possible. Read the shampoo instructions
and follow them closely.

Seat belts

The seat belts may be cleaned with
mild soap and water or with lukewarm
water.

Use a cloth or sponge. As you are clean-
ing, check the belts for excessive wear,
fraying, or cuts.

NOTICE

Do not use dye or bleach on the
belts—it may weaken them.

Do not use the belts until they be-
come dry.

Windows

The windows may be cleaned with any
household window cleaner.

NOTICE

When cleaning the inside of the rear
window, be careful not to scratch or
damage the heater wires or connec-
tors.

Air conditioning control panel, audio
panel, instrument panel, console panel,
and switches

Use a soft damp cloth for cleaning.

Soak a clean soft cloth in water or luke-
warm water then lightly wipe off dirt.

NOTICE

Do not use organic substances (sol-
vents, kerosene, alcohol, gasoline,
etc.) or alkaline or acidic solutions.
These chemicals can cause discol-
oring, staining or peeling of the
surface.

If you use cleaners or polishing
agents, make sure their ingredients
do not include the substances men-
tioned above.

If you use a liquid car freshener, do
not spill the liquid onto the ve-
hicle’s interior surfaces. It may con-
tain the ingredients mentioned
above. Immediately clean any spill
using the method mentioned above.

Leather interior

The leather upholstery may be cleaned
with neutral detergent for wool.

Remove dirt using a soft cloth dampened
with 5% solution of neutral detergent for
wool. Then thoroughly wipe off all traces
of detergent with a clean damp cloth.

After cleaning or whenever any part of the
leather gets wet, dry with a soft clean
cloth. Allow the leather to dry in a venti-
lated shaded area.

«
...
68
69
70
71
72
...
»

Summary of Contents for Corolla 2008























































































































































































































































































































Reviews:

No comments

Related manuals for Corolla 2008

Brand: Federal Signal Corporation Pages: 8

Brand: Federal Signal Corporation Pages: 8

Brand: Yakima Pages: 12

Brand: JEHNERT SOUND DESIGN Pages: 8

Experience Series

Brand: Rainbow Pages: 19

Brand: Yakima Pages: 12

Brand: Yakima Pages: 12

2007 MazdaSpeed6

Brand: Mazda Pages: 12

Brand: Toro Pages: 24

Ford 4” UNI-CAM

Brand: Nav TV Pages: 6

2007 9-3 Remote Starter

Brand: Saab Pages: 304

Brand: Westfalia Pages: 10

Brand: RBO Pages: 15

Brand: Axxess Pages: 8

Brand: Dodge Pages: 276

ZapCharger Portable C1

Brand: ZAPTEC Pages: 20

Security Cage Kit

Brand: Toro Pages: 8

Brand: Ranger design Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands