Toyota Corolla 2008 Owner'S Manual Download Page 195 | Manualshive

Page: 195 / 310

background image

’08 Corolla_U (L/O 0706)

107

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

If the fuel tank is not empty or the fuel
tank cap is not loose...

There is a problem somewhere in the
engine, emission control system, elec-
tronic throttle control system, automatic
transmission electrical system or warn-
ing light system itself.

Contact your Toyota dealer as soon as
possible to service the vehicle.

If engine speed does not increase when
the accelerator pedal is depressed, there
may be a problem somewhere in the elec-
tronic throttle control system.

At this time, vibration may occur. Howev-
er, if you depress the accelerator pedal
more firmly and slowly, you can drive your
vehicle at low speeds. Have your vehicle
checked by your Toyota dealer as soon as
possible.

Even if the abnormality of the electronic
throttle control system is corrected during
low speed driving, the system may not be
recovered until the engine is stopped and
the ignition key is turned to “ACC” or
“LOCK” position.

CAUTION

Be especially careful to prevent erro-
neous pedal operation.

Emissions Inspection and Maintenance
(I/M) programs

Your vehicle may not pass a state
emission inspection if the malfunction
indicator lamp remains on. Contact your
Toyota dealer to check your vehicle’s
emission control system and OBD
(On−Board Diagnostics) system before
taking your vehicle for the inspection.

For details, see “Emissions Inspection and
Maintenance (I/M) programs” on page 252
in Section 6.

(f) Low Fuel Level Warning Light

This light comes on when the fuel level
in the tank becomes nearly empty. Fill up
the tank as soon as possible.

On inclines or curves, due to the move-
ment of fuel in the tank, the low fuel level
warning light may come on earlier than
usual.

(g) Low Engine Oil Pressure Warning

Light

This light warns that the engine oil pres-
sure is too low.

If it flickers or stays on while you are
driving, pull off the road to a safe place
and stop the engine immediately. Call a
Toyota dealer or qualified repair shop for
assistance.

The light may occasionally flicker when
the engine is idling or it may come on
briefly after a hard stop. There is no
cause for concern if it then goes out when
the engine is accelerated slightly.

The light may come on when the oil level
is extremely low. It is not designed to
indicate low oil level, and the oil level
must be checked using the level dipstick.

NOTICE

Do not drive the vehicle with the
warning light on—even for one block.
It may ruin the engine.

«
...
193
194
195
196
197
...
»

Summary of Contents for Corolla 2008























































































































































































































































































































Reviews:

No comments

Related manuals for Corolla 2008

Brand: GMC Pages: 499

Brand: Kia Pages: 290

Brand: Masterack Pages: 4

Brand: Over Armour Offroad Pages: 5

Brand: U.S. General Pages: 4

Brand: Nuna Pages: 17

Brand: JANE Pages: 58

Brand: Atera Pages: 3

Brand: Black Horse Pages: 5

Brand: Maserati Pages: 302

Brand: Caraudio-Systems Pages: 9

PRIME DESIGN HRR3-E-PM42

Brand: Safe Fleet Pages: 12

Brand: N.R. AUTOSEATS Pages: 8

Brand: Audi Pages: 4

Brand: Thule Pages: 15

Brand: VP Autoparts Pages: 2

Brand: Edelbrock Pages: 2

Brand: Metra Electronics Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands