Toyota Corolla 2008 Owner'S Manual Download Page 145 | Manualshive

Page: 145 / 310

background image

’08 Corolla_U (L/O 0706)

57

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

8. Front passenger’s seat belt buckle

switch

9. Airbag sensor assembly

The SRS side airbag and curtain shield
airbag system is controlled by the airbag
sensor assembly. The airbag sensor as-
sembly consists of a safing sensor and
airbag sensor.

In a severe side impact, the side and
curtain shield airbag sensor and/or the
curtain shield airbag sensor trigger(s) the
side airbag inflators and/or the curtain
shield airbag inflators. At this time a
chemical reaction in the inflators quickly
fills the airbags with non−toxic gas to help
restrain the lateral motion of the occu-
pants.

When the airbags inflate, they produce a
fairly loud noise and release some smoke
and residue along with non−toxic gas. This
does not indicate a fire. This smoke may
remain inside the vehicle for some time,
and may cause some minor irritation to
the eyes, skin or breathing. Be sure to
wash off any residue as soon as possible
to prevent any potential skin irritation with
soap and water. If you can safely exit
from the vehicle, you should do so imme-
diately.

Deployment of the airbags happens in a
fraction of a second, so the airbags must
inflate with considerable force. While the
system is designed to reduce serious inju-
ries, it may also cause minor burns or
abrasions and swelling.

Front seats as well as parts of the front
and rear pillars, and roof side rail may be
hot for several minutes, but the airbags
themselves will not be hot. The airbags
are designed to inflate only once.

CAUTION

SRS side airbags and curtain shield
airbags inflate with considerable
force. To reduce the possibility of
death or serious injury when they in-
flate, the driver, front passenger and
rear outside passengers must:

Wear their seat belts properly.

Remain properly seated with their
backs upright and against the seats
at all times.

Do not allow anyone to lean against
the door when the vehicle is in use,
since the side airbag and curtain
shield airbag could inflate with con-
siderable speed and force. Other-
wise, he/she may be killed or seri-
ously injured. Special care should
be taken especially when you have
a small child in the vehicle.

Sit up straight and well back in the
seat, distributing your weight evenly
in the seat. Do not apply excessive
weight to the outer side of the
seats with a side airbag, and to the
front pillar, rear pillar and roof side
rail with a curtain shield airbag.

«
...
143
144
145
146
147
...
»

Summary of Contents for Corolla 2008























































































































































































































































































































Reviews:

No comments

Related manuals for Corolla 2008

Brand: Xblitz Pages: 16

Brand: Roav Pages: 10

Brand: Kuda-Phonebase Pages: 3

Brand: Neuspeed Pages: 2

Brand: Edelbrock Pages: 1

Brand: FORM FIT Pages: 2

Brand: U & Me Brothers Pages: 6

Brand: Rola Pages: 3

Brand: Caltrend Pages: 2

Brand: Audiovox Pages: 1

EGR-3PVE-COLOUR

Brand: EGR Pages: 28

Brand: Metra Electronics Pages: 8

Brand: Fab Fours Pages: 13

Brand: Thule Pages: 4

Brand: Cadillac Pages: 2

Brand: Buick Pages: 20

1953 Traction Avant

Brand: CITROEN Pages: 26

Brand: Pogo Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands