Toyota Corolla 2008 Owner'S Manual Download Page 47 | Manualshive

Page: 47 / 310

background image

’08 Corolla_U (L/O 0706)

221

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

To avoid serious personal injury and
damage to your vehicle which might re-
sult from battery explosion, acid burns,
electrical burns, or damaged electronic
components, these instructions must be
followed precisely.

If you are unsure about how to follow this
procedure, we strongly recommend that
you seek the help of a competent me-
chanic or towing service.

CAUTION

Batteries contain sulfuric acid
which is poisonous and corrosive.
Wear protective safety glasses when
jump starting, and avoid spilling
acid on your skin, clothing, or ve-
hicle.

If you should accidentally get acid
on yourself or in your eyes, remove
any contaminated clothing and flush
the affected area with water imme-
diately. Then get immediate medical
attention. If possible, continue to
apply water with a sponge or cloth
while en route to the medical office.

The gas normally produced by a
battery will explode if a flame or
spark is brought near. Use only
standardized jumper cables and do
not smoke or light a match while
jump starting.

NOTICE

The battery used for boosting must
be 12 V. Do not jump start unless you
are sure that the booster battery is
correct.

JUMP STARTING PROCEDURE

1. If the booster battery is installed in

another vehicle, make sure the vehicles
are not touching. Turn off all unneces-
sary lights and accessories.

When boosting, use the battery of
matching or higher quality. Any other
battery may be difficult to jump start
with.

If jump starting is difficult, charge the
battery for several minutes.

2. If required, remove all the vent plugs

from the booster and discharged batter-
ies. Lay a cloth over the open vents
on the batteries. (This helps reduce the
explosion hazard, personal injuries and
burns.)

3. If the engine in the vehicle with the

booster battery is not running, start it
and let it run for a few minutes. During
jump starting, run the engine at about
2000 rpm with the accelerator pedal
lightly depressed.

(c) Jump starting

«
...
45
46
47
48
49
...
»

Summary of Contents for Corolla 2008























































































































































































































































































































Reviews:

No comments

Related manuals for Corolla 2008

Brand: Vauxhall Pages: 2

Brand: Axxess Pages: 8

Brand: Hama Pages: 40

Brand: Safe Fleet Pages: 38

Brand: Chevrolet Pages: 2

Stratus LHD 1997

Brand: Chrysler Pages: 1534

Brand: Dacia Pages: 238

Brand: WABCO Pages: 32

Brand: Saab Pages: 12

Brand: ACV Pages: 2

Brand: EUFAB Pages: 16

Brand: Needit Pages: 2

KIT ParkingSensor 814

Brand: Gemini Pages: 6

nERGY ETSA200R-PA

Brand: Soundoff Signal Pages: 3

Brand: Truma Pages: 10

Brand: Brodit Pages: 2

Brand: Saturn Pages: 432

Brand: Prime Design Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands