Toyota Corolla 2008 Owner'S Manual Download Page 155 | Manualshive

Page: 155 / 310

background image

’08 Corolla_U (L/O 0706)

67

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

A forward−facing child restraint sys-
tem should be allowed to be
installed on the front passenger
seat only when it is unavoidable.
Always move the seat as far back
as possible even if the front pas-
senger occupant classification indi-
cator light indicates “OFF”, because
the front passenger airbag could in-
flate with considerable speed and
force. Otherwise, the child may be
killed or seriously injured.

On vehicles with side airbags and
curtain shield airbags, do not allow
the child to lean his/her head or
any part of his/her body against the
door or the area of the seat, front
or rear pillar or roof side rail from
which the side airbags or curtain
shield airbags deploy even if the
child is seated in the child restraint
system. It is dangerous if the side
airbag and/or curtain shield airbag
inflate, and the impact could cause
death or serious injury to the child.

Do not use the seat belt extender
when installing a child restraint
system on the front or rear passen-
ger seat. If installing a child re-
straint system with the seat belt
extender connected to the seat belt,
the seat belt will not securely hold
the child restraint system, which
could cause death or serious injury
to the child or other passengers in
the event of collision.

Make sure you have complied with
all installation instructions provided
by the child restraint manufacturer
and that the system is properly se-
cured. If it is not secured properly,
it may cause death or serious injury
to the child in the event of a sud-
den stop or accident.

A child restraint system for a small
child or baby must itself be properly
restrained on the seat with the lap por-
tion of the lap/shoulder belt. You must
carefully consult the manufacturer’s in-
structions which accompany the child
restraint system.

To provide proper restraint, use a child
restraint system following the manufactur-
er’s instructions about the appropriate age
and size of the child for the child restraint
system.

Install the child restraint system correctly
following the instructions provided by its
manufacturer. General directions are also
provided under the following illustrations.

The child restraint system should be
installed on the rear seat. According to
accident statistics, the child is safer when
properly restrained in the rear seat than
in the front seat.

When not using the child restraint system,
keep it secured with the seat belt or place
it in the trunk or somewhere other than
the passenger compartment. This will pre-
vent it from injuring passengers in the
event of a sudden stop or accident.

—Child restraint system

«
...
153
154
155
156
157
...
»

Summary of Contents for Corolla 2008























































































































































































































































































































Reviews:

No comments

Related manuals for Corolla 2008

Brand: Jeda Pages: 8

Brand: Jeep Pages: 496

2011 grand cherokee

Brand: Jeep Pages: 22

2013 Grand Cherokee

Brand: Jeep Pages: 704

Brand: Jeep Pages: 558

Brand: Triumph Pages: 86

Brand: Neuspeed Pages: 2

MagicWatch MWE250

Brand: Waeco Pages: 172

Brand: Harman Kardon Pages: 16

Brand: TATA Motors Pages: 184

PW-50C Civilian

Brand: B&G electronics Pages: 7

Brand: Great Wall Pages: 18

Brand: WIX Pages: 2

Brand: HAKR Pages: 9

Brand: Lexus Pages: 82

Brand: Volvo Pages: 7

Civic Hatch 2017

Brand: Honda Pages: 687

Brand: Tesla Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands