Toyota Corolla 2008 Owner'S Manual Download Page 129 | Manualshive

Page: 129 / 310

background image

’08 Corolla_U (L/O 0706)

41

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

When a passenger’s shoulder belt is com-
pletely extended and is then retracted
even slightly, the belt is locked in that
position and cannot be extended. This fea-
ture is used to hold the child restraint
system securely. (For details, see “Child
restraint” on page 66 in this Section.) To
free the belt again, fully retract the belt
and then pull the belt out once more.

If the seat belt cannot be pulled out of the
retractor, firmly pull the belt and release
it. You will then be able to smoothly pull
the belt out of the retractor.

CAUTION

After inserting the tab, make sure
the tab and buckle are locked and
that the belt is not twisted.

Do not insert coins, clips, etc. in
the buckle as this may prevent you
from properly latching the tab and
buckle.

If the seat belt does not function
normally, immediately contact your
Toyota dealer. Do not use the seat
until the seat belt is fixed, because
it cannot protect an adult occupant
or your child from death or serious
injury.

Take up
slack

Too high

Keep as low on
hips as possible

Adjust the position of the lap and
shoulder belts.

Position the lap belt as low as possible
on your hips—not on your waist, then ad-
just it to a snug fit by pulling the shoulder
portion upward through the latch plate.

CAUTION

Both high−positioned lap belts and
loose−fitting belts could cause seri-
ous injuries due to sliding under
the lap belt during a collision or
other unintended event. Keep the
lap belt positioned as low on hips
as possible.

Do not place the shoulder belt un-
der your arm.

«
...
127
128
129
130
131
...
»

Summary of Contents for Corolla 2008























































































































































































































































































































Reviews:

No comments

Related manuals for Corolla 2008

Brand: Abarth Pages: 176

Brand: iDataLink Pages: 30

Brand: Jabra Pages: 2

Brand: Jabra Pages: 38

Reference Series

Brand: OEM Audio Pages: 29

PICASSO XSARA DESIRE 1.6 - MESUREMENT

Brand: CITROEN Pages: 2

LeisureWize EMOVE EM303A

Brand: Streetwize Pages: 20

Brand: Saab Pages: 445

Brand: Acura Pages: 2

2004 Vibe Navigation System

Brand: Pontiac Pages: 44

Brand: Yescom Pages: 4

Brand: Z Automotive Pages: 16

2016 Sandero Stepway

Brand: Renault Pages: 183

Brand: Skoda Pages: 165

Brand: Flash Cover Pages: 2

Brand: Porsche Pages: 98

Bluetooth Phone System 2010

Brand: Kia Pages: 16

Prime Design OCM-3032

Brand: Safe Fleet Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands