Toyota Corolla 2008 Owner'S Manual Download Page 221 | Manualshive

Page: 221 / 310

background image

’08 Corolla_U (L/O 0706)

133

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

Under certain circumstances, the cruise
control is temporarily cancelled:

When vehicle speed falls below 40
km/h (25 mph)

When vehicle stability control is acti-
vated

When vehicle speed drops 16 km/h (10
mph) below the set speed, the cruise con-
trol is cancelled and the set speed is
erased from memory.

The “CRUISE” indicator light remains on
to indicate that the system is still in op-
eration.

To turn the cruise control off, press the
“ON−OFF” button. Make sure the
“CRUISE” indicator light is off.

If the cruise control automatically cancels
out other than for the above cases, have
your vehicle checked by your Toyota deal-
er at the earliest opportunity.

RESUMING THE CRUISE CONTROL

If the cruise control is temporarily can-
celled, the cruising speed can be resumed
by pushing the lever up in the “+ RES”
direction.

Vehicle speed must be above 40 km/h (25
mph).

RESETTING TO A FASTER SPEED

Push the lever up in the “+ RES” direction
and hold it. Release the lever when the
desired speed is attained. While the lever
is held up, the vehicle will gradually gain
speed.

However, a faster way to reset is to ac-
celerate the vehicle and then push the
lever down in the “− SET” direction.

RESETTING TO A SLOWER SPEED

Push the lever down in the “− SET” direc-
tion and hold it. Release the lever when
the desired speed is attained. While the
lever is held down, the vehicle speed will
gradually decrease.

However, a faster way to reset is to de-
press the brake pedal and then push the
lever down in the “− SET” direction.

On vehicles with automatic transmission,
even if you turn off the overdrive switch,
with the cruise control on, engine braking
will not be applied because the cruise
control is not cancelled. To decrease the
vehicle speed, reset to a slower speed
with the cruise control lever or depress
the brake pedal. If you use the brake
pedal, cruise control is cancelled.

CRUISE CONTROL FAILURE WARNING

If the “CRUISE” indicator light flashes
when using the cruise control, press the
“ON−OFF” button to turn the system off
and then press it again to turn it on.

If any of the following conditions then oc-
curs, there is some trouble in the cruise
control system.

The indicator light does not come on.

The indicator light flashes again.

The indicator light goes out after it
comes on.

If this is the case, contact your Toyota
dealer and have your vehicle inspected.

«
...
219
220
221
222
223
...
»

Summary of Contents for Corolla 2008























































































































































































































































































































Reviews:

No comments

Related manuals for Corolla 2008

Brand: Metra Electronics Pages: 14

Brand: Warrior Products Pages: 3

Brand: Ford Pages: 12

Brand: B-Speech Pages: 4

Brand: NavLinkz Pages: 21

Brand: Bestop Pages: 31

Brand: Anker Technology Pages: 8

Brand: Prorack Pages: 15

Brand: MBRP Pages: 5

Brand: Speedtech Pages: 12

ChargePoint CT500-DSTAND

Brand: Coulomb Technologies Pages: 26

Brand: Yakima Pages: 9

$T-Rex TEX-51127 Installation Manual preview$

Brand: T-Rex Pages: 9

Brand: AirBedz Pages: 4

Brand: Kia Pages: 54

Brand: Ford Pages: 541

Brand: Thule Pages: 12

Brand: Akyga Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands