manualshive.com logo in svg

Toyota Corolla 2008, Owner'S Manual

The Toyota Corolla 2008 Owner's Manual is a comprehensive guide that provides users with detailed instructions on how to operate and maintain their vehicle. At manualshive.com, we offer this manual for free download, providing users with a convenient and easy way to access essential information about their Toyota Corolla 2008.

Share
Download
background image

’08 Corolla_U (L/O 0706)

270

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

The tires on your Toyota have built−in
tread wear indicators to help you
know when the tires need replace-
ment. When the tread depth wears to
1.6 mm (0.06 in.) or less,  the indica-
tors will appear. If you can see the
indicators in two or more adjacent
grooves, the tire should be replaced.
The lower the tread, the higher the
risk of skidding.

The effectiveness of snow tires is
lost if the tread wears down below
4 mm (0.16 in.).

If you have tire damage such as
cuts, splits, cracks deep enough to
expose the fabric, or bulges indi-
cating internal damage, the tire
should be replaced.

If a tire often goes flat or cannot be
properly repaired due to the size or
location of a cut or other damage, it
should be replaced. If you are not
sure, consult with your Toyota dealer.

If air loss occurs while driving, do not
continue driving. Driving even a short
distance can damage a tire beyond
repair.

Any tires which are over 6 years
old must be checked by a qualified
technician even  if damage is not
obvious.

Tires deteriorate with age even if they
have never or seldom been used.

This applies also to the spare tire and
tires stored for future use.

REPLACING YOUR TIRES

When replacing a tire, use a tire of
the same size and construction,
and the same or greater maximum
load as the originally installed
tires.

Using any other size or type of tire
may seriously affect handling, ride,
speedometer/odometer calibration,
ground clearance, and clearance be-
tween the body and tires or snow
chains.

Check that the maximum load of the
replaced tire is greater than 1/2 of the
Gross Axle Weight Ratings (GAWR)
of either the front axle or the rear
axle, whichever is greater. As for the
maximum load of the tire, see the load
limit at maximum cold tire inflation
pressure mentioned on the sidewall
of the tire, and as for the Gross Axle
Weight Ratings (GAWR), see the Cer-
tification Label.

For details about the side wall of the
tire and the Certification Label, see
pages 186 and 188.

Summary of Contents for Corolla 2008























































































































































































































































































































Reviews:

No comments

Related manuals for Corolla 2008

ULTIMATE SPEED CARBON Assembly And Safety Advice preview
CARBON
Brand: ULTIMATE SPEED Pages: 19
Jetter JX3-BN-CAN Manual preview
JX3-BN-CAN
Brand: Jetter Pages: 4
K&K M5700N Manual preview
M5700N
Brand: K&K Pages: 8
K&K M4700 Manual preview
M4700
Brand: K&K Pages: 20
K&K M3500N Manual preview
M3500N
Brand: K&K Pages: 6
K&K M2500 Manual preview
M2500
Brand: K&K Pages: 3
K&K M1500 Manual preview
M1500
Brand: K&K Pages: 3
Kia Picanto 2015 Quick Reference Manual preview
Picanto 2015
Brand: Kia Pages: 10
Toyota AURION 2013 Owner'S Manual preview
AURION 2013
Brand: Toyota Pages: 371
Yuasa SmartShot Automatic 12V 1.5 Amp 5 Stage Technical Manual preview
SmartShot Automatic 12V 1.5 Amp 5 Stage
Brand: Yuasa Pages: 44
AutoWatch 457 Rli Wiring Diagram preview
457 Rli
Brand: AutoWatch Pages: 4
Pontiac 2004 Vibe Navigation System Owner'S Manual preview
2004 Vibe Navigation System
Brand: Pontiac Pages: 44
Chevrolet Impala Limited 2014 Owner'S Manual preview
Impala Limited 2014
Brand: Chevrolet Pages: 356
Tesla MODEL Y Owner'S Manual preview
MODEL Y
Brand: Tesla Pages: 274
Rugged Ridge 11232.20 Quick Start Manual preview
11232.20
Brand: Rugged Ridge Pages: 2
AL-KO AKS 1300 Operating Instructions Manual preview
AKS 1300
Brand: AL-KO Pages: 40
Lexus LS 460 2011 Owner'S Manual preview
LS 460 2011
Brand: Lexus Pages: 830
Suzuki SX4 2016 Owner'S Manual preview
SX4 2016
Brand: Suzuki Pages: 504

Brands by name

Popular brands

Load more brands