Toyota Corolla 2008 Owner'S Manual Download Page 167

Page: 167 / 310

’08 Corolla_U (L/O 0706)

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

To remove the booster seat:

Press the buckle release button and allow
the belt to retract.

Follow the procedure below for a child
restraint system that requires the use
of a top strap.

Anchor brackets

Symbol

Use the anchor brackets on the luggage
compartment to attach the top strap.

Anchor brackets are installed for each
rear seating position.

This symbol indicates the locations of the
anchor brackets.

—Using a top strap

Summary of Contents for Corolla 2008























































































































































































































































































































Search results

Summary of Contents for Corolla 2008

Reviews:

Related manuals for Corolla 2008

Brands by name

Popular brands

Toyota Corolla 2008, Owner'S Manual

Search results

Summary of Contents for Corolla 2008

Reviews:

Related manuals for Corolla 2008

Brands by name

Popular brands