Toyota Corolla 2008 Owner'S Manual Download Page 135 | Manualshive

Page: 135 / 310

background image

’08 Corolla_U (L/O 0706)

47

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

This warning light system monitors the
airbag sensor assembly, front airbag sen-
sors, side and curtain shield airbag sen-
sors, curtain shield airbag sensors, driv-
er’s seat position sensor, driver’s seat belt
buckle switch, front passenger occupant
classification system and indicator light,
front passenger’s seat belt buckle switch,
seat belt pretensioner assemblies, inflat-
ors, interconnecting wiring and power
sources. (For details, see “Service remind-
er indicators and warning buzzers” on
page 102 in Section 1−6.)

If any of the following conditions occurs,
this indicates a malfunction of the airbags
or seat belt pretensioners. Contact your
Toyota dealer as soon as possible.

The light does not come on when the
ignition key is turned to the “ON” posi-
tion or remains on for more than 6
seconds or flashes.

The light comes on or starts flashing
while driving.

If any seat belt does not retract or can
not be pulled out due to a malfunction
or activation of the relevant seat belt
pretensioner.

The seat belt pretensioner assembly or
surrounding area has been damaged.

In the following cases, contact your Toyota
dealer as soon as possible:

The front of the vehicle (shaded in the
illustration) was involved in an accident
that was not severe enough to cause
the seat belt pretensioners to operate.

Either seat belt pretensioner assembly
or surrounding area is scratched,
cracked, or otherwise damaged.

The SRS (Supplemental Restraint Sys-
tem) front airbags are designed to pro-
vide further protection for the driver
and front passenger in addition to the
primary safety protection provided by
the seat belts.

Your vehicle is equipped with “ADVANCED
AIRBAGS” designed based on US motor
vehicle safety standards (FMVSS208). The
airbag system controls airbag deployment
power for the driver and front passenger.
The driver airbag system consists of the
driver seat’s position sensor etc. The front
passenger’s airbag system consists of the
front passenger occupant classification
sensor etc.

SRS airbags—
—SRS driver airbag and front
passenger airbag

«
...
133
134
135
136
137
...
»

Summary of Contents for Corolla 2008























































































































































































































































































































Reviews:

No comments

Related manuals for Corolla 2008

Brand: Vauxhall Pages: 2

Brand: RAM Pages: 20

Brand: Aries Pages: 3

Brand: Horn Tools Pages: 6

Brand: Edelbrock Pages: 2

Brand: Whispbar Pages: 77

Brand: Volvo Pages: 188

MagicWatch MWE250

Brand: Waeco Pages: 172

MAGNUM RT Series

Brand: Raptor Series Pages: 6

STEALTH POWER RBP-216-SP

Brand: RBP Pages: 16

STREET SUPER SHIFTER

Brand: HURST Pages: 2

Brand: Metra Electronics Pages: 8

Brand: BMW Pages: 55

Brand: Whispbar Pages: 15

Brand: M7 SPEED Pages: 6

Brand: Kia Pages: 51

Brand: Hama Pages: 4

Brand: Volvo Pages: 230

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands