Toyota Corolla 2008 Owner'S Manual Download Page 198 | Manualshive

Page: 198 / 310

background image

’08 Corolla_U (L/O 0706)

110

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

(l)

Low Windshield Washer Fluid Level
Warning Light (for vehicles sold in
Canada)

The light warns that the windshield washer
fluid level is too low. Add washer fluid at
your earliest opportunity. (For instructions,
see “Adding washer fluid” on page 279 in
Section 7−3.)

(m) “VSC” Warning Light

The light warns that there is a problem
somewhere in the vehicle stability control
system or the traction control system.

The light will come on when the ignition
key is turned to “ON”, and will go off after
about a few seconds.

If the light comes on, the vehicle stability
control system and traction control system
do not work. However, as conventional
braking operates when applied, there is no
problem to continue your driving.

In the following cases, contact your Toyota
dealer:

The light does not come on after the
ignition is turned to on.

The light is left on after the ignition is
turned to on.

The light comes on while driving.

The slip indicator light/traction control sys-
tem off indicator light will come on when
the “VSC” warning light comes on even if
the “TR

A

C OFF” switch is not pushed.

(n) Engine Oil Replacement Reminder

Light (for vehicles sold in the
U.S.A.)

This light reminds you when to replace
the engine oil.

This light will come on when the ignition
key is turned to “ON” and will go off after
about a few seconds.

When you drive for about 7200 km (4500
miles) after the engine oil replacement,
this light illuminates for 3 seconds and
then flashes for 12 seconds with the igni-
tion key turned to the “ON” position. If
you continue driving without replacing the
engine oil, and if the distance driven ex-
ceeds 8000 km (5000 miles), the light will
come on after the ignition key is turned
to the “ON” position. The light will remain
on thereafter.

If the light is flashing, we recommend that
you replace the engine oil at an early
opportunity depending on the driving and
road conditions.

The system must be reset after the en-
gine oil replacement. Reset the system by
the following procedure:

1. Turn the ignition key to the “ACC” or

“LOCK” position with the odometer
reading shown. (For details, see
“Odometer and two trip meters” on
page 100 in this Section.)

2. Turn the ignition key to the “ON” posi-

tion while holding down the trip meter
reset knob.

Hold down the button for at least 5 sec-
onds. The odometer indicates “000000”
and the light goes off.

If the system fails to reset, the light will
continue flashing.

(o) Key Reminder Buzzer

This buzzer reminds you to remove the
key when you open the driver’s door with
the ignition key in the “ACC” or “LOCK”
position.

(p) Light Reminder Buzzer

This buzzer will sound if the headlight
switch is left on and the driver’s door is
opened with the key removed from the
ignition switch.

«
...
196
197
198
199
200
...
»

Summary of Contents for Corolla 2008























































































































































































































































































































Reviews:

No comments

Related manuals for Corolla 2008

SP200 - QUICKSTART GUIDE 1

Brand: Jabra Pages: 2

BT150 - Headset - Over-the-ear

Brand: Jabra Pages: 2

BLACK STEEL S2560

Brand: Fab Fours Pages: 9

Brand: Skoda Pages: 165

Brand: Chevrolet Pages: 428

Brand: Cadillac Pages: 409

Brand: Fortin Pages: 9

Brand: Oldsmobile Pages: 380

INDICA eV2 XETA CNG

Brand: TATA Motors Pages: 24

Brand: PAC Pages: 5

Brand: Percon Pages: 49

Brand: PUTCO Pages: 3

Brand: Kolpin Pages: 6

Brand: Prorack Pages: 14

PerfectView CRT300

Brand: Waeco Pages: 200

Forester 2.5X 2003

Brand: Subaru Pages: 44

Brand: Mont Blanc Pages: 10

2013 Accord Sedan

Brand: Honda Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands