Toyota Corolla 2008 Owner'S Manual Download Page 194 | Manualshive

Page: 194 / 310

background image

’08 Corolla_U (L/O 0706)

106

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

(c) Front Passenger’s Seat Belt

Reminder Light and Buzzer

The light and buzzer act as a reminder to
have the front passenger buckle up the
seat belt.

Once the ignition key is turned to “ON” or
“START”, the reminder light flashes if a
passenger sits in the front passenger seat
and does not fasten the seat belt.

If the vehicle speed rises above 15 km/h
(9 mph) with the seat belt unfastened, the
buzzer will sound for about 10 seconds.
Then, if the seat belt is still unfastened,
the buzzer will sound in a different tone
for 20 seconds. Even if the vehicle speed
drops below 15 km/h (9 mph), the buzzer
will continue to sound. To stop the buzzer,
fasten the seat belt. If the buzzer still
sounds, make sure the driver’s seat belt
is fastened.

If luggage or other load is placed on the
front passenger seat, depending on its
weight, the reminder light to flash and
buzzer to sound.

(d) Charging System Warning Light

This warning light comes on when the
ignition switch is turned to the “ON” posi-
tion, and goes off when the engine is
started.

When there are problems in the charging
system while the engine is running, the
warning light comes on.

NOTICE

When the charging system warning
light comes on while the engine is
running, malfunctions such as the en-
gine drive belt being broken may have
occurred. If the warning light comes
on, immediately stop the vehicle in a
safe place and contact your Toyota
dealer.

(e) Malfunction Indicator Lamp

This lamp comes on when the ignition
key is turned to the “ON” position and
goes off after the engine starts. This
means that the warning light system is
operating properly.

If the lamp remains on, or the lamp
comes on while driving, first check the
followings.

Empty fuel tank

If the fuel tank is empty, refuel immedi-
ately.

Loose fuel tank cap

If the fuel tank cap is loose, securely
tighten it.

These cases are temporary malfunctions.
The malfunction indicator lamp will go off
after taking several driving trips.

If the lamp does not go off even after
several trips, contact your Toyota dealer
as soon as possible.

«
...
192
193
194
195
196
...
»

Summary of Contents for Corolla 2008























































































































































































































































































































Reviews:

No comments

Related manuals for Corolla 2008

Brand: Panasonic Pages: 2

CYRC50U - UNIVERSAL REAR-VIEW CAMERA

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 12

Brand: Harmar Mobility Pages: 10

Brand: Haibang Pages: 6

Brand: Subaru Pages: 99

1973 Convertible

Brand: Volkswagen Pages: 80

CB-796IG2-CIGD-R

Brand: CARRYBOY Pages: 4

Brand: GMC Pages: 428

Brand: Metra Electronics Pages: 20

BTFREQ PRO BTFMPD3SR

Brand: Scosche Pages: 16

Parrot MKi + ParrotCK3100 range LOGAN

Brand: Parrot Pages: 10

2917 Nstallation

Brand: Edelbrock Pages: 1

Brand: Volvo Pages: 18

Brand: Ford Pages: 17

Brand: FORM FIT Pages: 2

Brand: Cadillac Pages: 416

PRO-YD-DINT98-HL

Brand: Spyder Auto Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands