Toyota Corolla 2008 Owner'S Manual Download Page 158 | Manualshive

Page: 158 / 310

background image

’08 Corolla_U (L/O 0706)

70

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

To install the infant seat:

1. Run the lap and shoulder belt through

or around the infant seat following the
instructions provided by its manufactur-
er and insert the tab into the buckle
taking care not to twist the belt. Keep
the lap portion of the belt tight.

CAUTION

After inserting the tab, make sure
the tab and buckle are locked and
that the lap and shoulder portions
of the belt are not twisted.

Do not insert coins, clips, etc. in
the buckle as this may prevent your
child from properly latching the tab
and buckle.

If the seat belt does not function
normally, it cannot protect your
child from death or serious injury.
Contact your Toyota dealer immedi-
ately. Do not install the child
restraint system on the seat until
the seat belt is fixed.

2. Fully extend the shoulder belt to put it

in the lock mode. When the belt is
then retracted even slightly, it cannot
be extended.

To hold the infant seat securely, make
sure the belt is in the lock mode before
letting the belt retract.

«
...
156
157
158
159
160
...
»

Summary of Contents for Corolla 2008























































































































































































































































































































Reviews:

No comments

Related manuals for Corolla 2008

Brand: U.S. General Pages: 4

Brand: Mazda Pages: 13

Brand: Gator Pages: 2

Brand: Black Horse Off Road Pages: 7

Brand: Mitsubishi MOTORS Pages: 416

Magic Watch MWE-850-4DSM

Brand: Waeco Pages: 204

Brand: Prorack Pages: 14

Brand: TOP VEHICLE TECH Pages: 8

1995 C/K Pickup

Brand: Chevrolet Pages: 483

Brand: HOLDEN Pages: 330

Brand: Husky Pages: 8

Brand: Honda Pages: 330

Tipper Remote Kit

Brand: Nugent Pages: 21

Brand: Volvo Pages: 286

Brand: Cadillac Pages: 339

Brand: Curt Group Pages: 2

Brand: NavLinkz Pages: 24

Brand: Ford Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands