Toyota Corolla 2008 Owner'S Manual Download Page 191

Page: 191 / 310

’08 Corolla_U (L/O 0706)

103

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

If the indicator or buzzer comes on...

Do this.

(h)

Take vehicle to Toyota dealer.
If brake system warning light is also on, stop immediately and contact Toyota dealer.

(i)

Close all doors.

(j)

Take vehicle to Toyota dealer immediately.

(k)

Adjust tire inflation pressure. If the light comes on after blinking for 1 minute, contact
Toyota dealer.

(l)

Add washer fluid.

(m)

Take vehicle to Toyota dealer.

(n)

Replace engine oil.

Summary of Contents for Corolla 2008























































































































































































































































































































Search results

Summary of Contents for Corolla 2008

Reviews:

Related manuals for Corolla 2008

Brands by name

Popular brands

Toyota Corolla 2008, Owner'S Manual

Search results

Summary of Contents for Corolla 2008

Reviews:

Related manuals for Corolla 2008

Brands by name

Popular brands