Toyota Corolla 2008 Owner'S Manual Download Page 124

Page: 124 / 310

’08 Corolla_U (L/O 0706)

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

While adjusting the seat, do not put
your hands under the seat or near
the moving parts. Otherwise, your
hands or fingers may be caught and
injured.

1. SEAT POSITION ADJUSTING LEVER

Hold the center of the lever and pull it
up. Then slide the seat to the desired
position with slight body pressure and
release the lever.

2. SEAT CUSHION HEIGHT ADJUSTING

LEVER

Pull up or push down the lever.

3. SEATBACK ANGLE ADJUSTING

LEVER

Lean forward and pull the lever up.
Then lean back to the desired angle
and release the lever.

—Adjusting front seats

Summary of Contents for Corolla 2008























































































































































































































































































































Search results

Summary of Contents for Corolla 2008

Reviews:

Related manuals for Corolla 2008

Brands by name

Popular brands

Toyota Corolla 2008, Owner'S Manual

Search results

Summary of Contents for Corolla 2008

Reviews:

Related manuals for Corolla 2008

Brands by name

Popular brands