Toyota Corolla 2008 Owner'S Manual Download Page 33 | Manualshive

Page: 33 / 310

background image

’08 Corolla_U (L/O 0706)

207

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

NOTICE

Do not crank for more than 30 se-
conds at a time. This may overheat
the starter and wiring systems.

Do not race a cold engine.

If the engine becomes difficult to
start or stalls frequently, have the
engine checked immediately.

Always slow down in gusty crosswinds.
This will allow you much better control.

Drive slowly onto curbs and, if pos-
sible, at a right angle. Avoid driving
onto high, sharp−edged objects and
other road hazards. Failure to do so
can lead to severe tire damage such
as a tire burst.

Drive slowly when passing over bumps
or travelling on a bumpy road. Other-
wise, the impact could cause severe
damage to the tires and/or wheels.

When parking on a hill, turn the front
wheels until they touch the curb so
that the vehicle will not roll. Apply the
parking brake, and place the transmis-
sion in “P” (automatic) or in first or
reverse (manual). If necessary, block
the wheels.

Washing your vehicle or driving through
deep water may get the brakes wet. To
see whether they are wet, check that
there is no traffic near you, and then
press the pedal lightly. If you do not
feel a normal braking force, the brakes
are probably wet. To dry them, drive
the vehicle cautiously while lightly
pressing the brake pedal with the park-
ing brake applied. If they still do not
work safely, pull to the side of the road
and call a Toyota dealer for assistance.

CAUTION

Before driving off, make sure that
the parking brake is fully released
and the parking brake reminder
light is off.

Do not leave your vehicle unat-
tended while the engine is running.

Do not rest your foot on the brake
pedal while driving. It can cause
dangerous overheating, needless
wear, and poor fuel economy.

To drive down a long or steep hill,
reduce your speed and downshift.
Remember, if you ride the brakes
excessively, they may overheat and
not work properly.

Tips for driving in various
conditions

«
...
31
32
33
34
35
...
»

Summary of Contents for Corolla 2008























































































































































































































































































































Reviews:

No comments

Related manuals for Corolla 2008

Brand: Davis Instruments Pages: 16

Brand: Jeep Pages: 5

Brand: Jeep Pages: 6

Grand Cherokee SRT 2014

Brand: Jeep Pages: 345

Grand Cherokee 2015

Brand: Jeep Pages: 236

Brand: Jeep Pages: 18

Brand: Jeep Pages: 24

Brand: Jeep Pages: 560

Brand: Jeep Pages: 525

Brand: Jeep Pages: 308

Brand: Jeep Pages: 86

Brand: Jeep Pages: 638

Brand: Jeep Pages: 9

Brand: Jeep Pages: 51

Brand: Jeep Pages: 4

Brand: Jeep Pages: 50

Grand Cherokee SRT 2014

Brand: Jeep Pages: 118

2014 Grand Cherokee

Brand: Jeep Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands