Toyota Corolla 2008 Owner'S Manual Download Page 217 | Manualshive

Page: 217 / 310

background image

’08 Corolla_U (L/O 0706)

129

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

REPLACING TIRES AND WHEELS

When replacing the tires and wheels, be
sure to install tire pressure warning valves
and transmitters. ID codes on the tire
pressure warning valves and transmitters
are registered in the tire pressure warning
ECU. When replacing a tire pressure
warning valve and transmitter, it is neces-
sary to register the ID code of tire pres-
sure warning valve and transmitter. Have
the ID code registered by your Toyota
dealer.

If the ID code is not registered, the sys-
tem will not work properly. After about 20
minutes, the tire pressure warning light
comes on after blinking for 1 minute to
indicate a system malfunction.

NOTICE

When the tires or tire pressure warn-
ing valves and transmitters must be
replaced, have them replaced by your
Toyota dealer. The tire pressure warn-
ing valves and transmitters will be
affected by the installation or removal
of tires.

TIRE PRESSURE WARNING SYSTEM
RESET SWITCH

When initializing the system, the present
tire inflation pressure is stored as stan-
dard. The tire pressure warning system
determines decreased air pressure by
comparing the present and the standard
tire inflation pressures. When you change
the set tire inflation pressure, it is neces-
sary to initialize the tire pressure warning
system.

When changing the tire size

To initialize the system, perform the fol-
lowing:

1. Park the vehicle in a safe place and

turn the ignition key to the “ACC” or
“LOCK” position.

2. Adjust the pressure of all the installed

tires to the specified cold tire inflation
pressure level. (See “Tires” on page
292 in Section 8.)

3. Turn the ignition key to the “ON” posi-

tion.

4. Push and hold the tire pressure warn-

ing reset switch until the tire pressure
warning light blinks slowly three times.

5. Wait for a few minutes with the ignition

key in the “ON” position, and then turn
the ignition key to the “ACC” or
“LOCK” position.

If you push the tire pressure reset switch
while vehicle is moving, initialization is not
performed.

If you push the tire pressure reset switch
accidentally and initialization is performed,
adjust the tire inflation pressure to the
specified level and initialize the system
again.

«
...
215
216
217
218
219
...
»

Summary of Contents for Corolla 2008























































































































































































































































































































Reviews:

No comments

Related manuals for Corolla 2008

PRIME DESIGN VCR 326

Brand: Safe Fleet Pages: 16

Prime Design VBC PC11

Brand: Safe Fleet Pages: 8

Prime Design AR1418

Brand: Safe Fleet Pages: 4

Brand: REVCAMUK Pages: 4

LeisureWize EMOVE EM303A

Brand: Streetwize Pages: 20

Brand: Harman Kardon Pages: 16

Brand: TATA Motors Pages: 184

PW-50C Civilian

Brand: B&G electronics Pages: 7

Brand: Thule Pages: 8

Brand: Whelen Engineering Company Pages: 9

Dunlop L.D02.C.M

Brand: Sumitomo Pages: 22

Brand: Yutrax Pages: 8

Brand: S3 Power Sports Pages: 2

2004 Impreza OUTBACK SPORT

Brand: Subaru Pages: 34

Brand: TOPPOINT Pages: 2

Brand: TATA Motors Pages: 232

Brand: Mazda Pages: 14

Brand: Brodit Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands