Toshiba Strata CTX, Programming Manual

Page: 336 / 533

Telephone Button Programming
300 Series Programs
13-58
Strata CTX Programming - Part 3:Telephone Button Programming 04/03
308-01 Auto Release
)%
, n,
+ROG
,
n = 1. Disable
2. Detect 95ms
3. Detect 450ms (default)
Select the Automatic Release timing.
Note Select Disable if the CO does not send the automatic release
signal to the loop start trunk.
308-02 Short Flash
)%
, n,
+ROG
,
n = 0~15, where 1 = 100msec.
(default = 5, which is .5
seconds)
0 = no flash
Select Short Flash Time. When a telephone initiates the short flash
signal to the CO line it is connected to (using the short Flash feature
button or access code #450) the duration of a short flash is
determined by this command. Normally this signal is used to hook
flash a centrex line. The short flash range is 0 to 1.5 seconds in
increments of 0.1 seconds.
308-03 Long Flash
)%
, n,
+ROG
n = 0, 5, 10, 15, 20, 25 and 30,
where 5 = .5 seconds.
(default = 20) Select Long Flash Time. When a telephone initiates the long flash
signal to the CO line it is connected to (using the Long Flash feature
button or access code #451) the duration of a long flash is determined
by this command. Normally this signal is used to disconnect the line.
The long flash range is 0 to 3 seconds in increments of 0.5 seconds.
308-04 Pause after Flash
)%
, n,
+ROG
n = 0~5, 0 = immediately sent,
and 1sec.delay to
5sec.delay
(default = 1 second delay
before sending digits)
Pause time after flash: After a flash signal is sent to a CO line, this
timer determines when the line will start to send the dialed digits to
the other end.
308-04 Response Timer
)%
, n,
+ROG
n = 0~3000 The response timer is for analog DID/TIE lines that have the “start
method” set for “Timing” in Program 300-06. After a line is seized this
timer determines when the line will start to send the dialed digits to
the other end.
Possible Values 0=immediatly sent, and 50msec.delay to
500msec.delay. (default=500mseconds delay before sending digits).
309 Direct Inward Dialing
,
+ROG
This command assigns DID Number Analysis Table to ILG.
309-00 ILG Number
n,
+ROG
n = 1~32 (CTX100)
1~50 (CTX670 Basic)
1~128 (CTX670 Exp.) Select the ILG number.
309-01 DID Number
)%
, n,
+ROG
n = 1~7 digits may include wild
card “?” where “?” = 0~9 Enter a DID number.
309-02 MOH Source
)%
, n,
+ROG
n = 1. Quiet Tone
2. External 1 (default)
3. External 2
4. External 3
5. External 4
6. External 5
7. External 6
8. External 7
9. External 8
10. External 9
11. External 10
12. External 11
13. External 12
14. External 13
15. External 14
16. External 15
Set Music On Hold for Analog ISDN DID Trunk
309-03 GCO Key Group
)%
, n,
+ROG
n = 0~32 (CTX100)
0~50 (CTX670 Basic)
0~128 (CTX670 Exp.)
(default = 0) GCO Key Group number.
309-04 Pool Key Group
)%
, n,
+ROG
n = 0~32 (CTX100)
0~50 (CTX670 Basic)
0~128 (CTX670 Exp.)
(default = 0) Pooled Line Key Group
Programs 303~315
(continued)
Button Sequence Value(s) Summary