Sperry Marine Visionmaster FT ECDIS User Manual Download Page 506

Page: 506 / 531

System

ECDIS User Guide

13-22

65900012

Dual Radar – Diagnostic Functions

On dual radar the following diagnostic functions
contain read-only data for each channel:

•

PM (Performance Monitor)

•

TCVR Config

•

TCVR Data

•

TCVR BITE

To view the data for each channel click on either

Channel 1

Channel 2

tab buttons.

In PM (Performance Monitor) the monitoring mode (Receiver or System)
tune levels may be separately adjusted for each transceiver channel.

Summary of Contents for Visionmaster FT ECDIS




















































































































































































































































































































































































































































































































































Search results

Summary of Contents for Visionmaster FT ECDIS

Reviews:

Related manuals for Visionmaster FT ECDIS

Brands by name

Popular brands

Sperry Marine Visionmaster FT ECDIS, User Manual

Search results

Summary of Contents for Visionmaster FT ECDIS

Reviews:

Related manuals for Visionmaster FT ECDIS

Brands by name

Popular brands