Sperry Marine Visionmaster FT ECDIS User Manual Download Page 323

Page: 323 / 531

ECDIS User Guide

Alerts

65900012

7-25

Alert Type

Description

Priority

Notes

Long Mute Length

The mute length setting is longer than recommended or is

unlimited.

Warning

Lost Connection

Lost connection to Distribution Service

Warning

Lost Echo Reference

The Echo Reference Target is lost

Warning

Lost Target

Target is lost

Warning

Low Turn Rate Order

Turn Rate Order lower than minimum recommended. Monitor

steering closely. Increase turn rate to improve steering

effectiveness in this mode, especially if high winds are influencing

the vessel.

Warning

Low Video Level

The video level has dropped below the minimum threshold

Warning

Magnetic Course Over

Ground Unusable

Sensor Magnetic Course Over Ground Integrity VisionMaster FT

Alarm or

Caution

Depending on

configuration

Magnetic Heading

Unusable

Sensor Magnetic Heading Integrity VisionMaster FT

Alarm or

Warning

Magnetic Sensor

Heading Unusable

Sensor Magnetic Sensor Heading Integrity VisionMaster FT

Alarm or

Caution

Depending on

configuration

Magnetic Set and Drift

Unusable

Sensor Magnetic Set and Drift Integrity VisionMaster FT

Alarm or

Caution

Depending on

configuration

Magnetic Variation

Unusable

Sensor Magnetic Variation Integrity VisionMaster FT

Alarm or

Caution

Depending on

configuration

Maneuver Time

Time to trial maneuver is less than 30sec.

Warning

Mariner Object

Database Is Corrupt

The mariner object database has corrupt data for one or more

mariner objects and these mariner objects are being ignored.

Warning

Mariner Objects

Database Errors

Mariner objects are currently unavailable due to database

operation(s) that failed to execute.

Warning

Summary of Contents for Visionmaster FT ECDIS




















































































































































































































































































































































































































































































































































Search results

Summary of Contents for Visionmaster FT ECDIS

Reviews:

Related manuals for Visionmaster FT ECDIS

Brands by name

Popular brands

Sperry Marine Visionmaster FT ECDIS, User Manual

Search results

Summary of Contents for Visionmaster FT ECDIS

Reviews:

Related manuals for Visionmaster FT ECDIS

Brands by name

Popular brands