Sperry Marine Visionmaster FT ECDIS User Manual Download Page 319

Page: 319 / 531

ECDIS User Guide

Alerts

65900012

7-21

Alert Type

Description

Priority

Notes

Dual Homing Config

Error

Conflict detected in VMFT configuration of Dual Homing and actual

setup.

Warning

Dual Homing Fault

No connection on one or more of the network adapters.

Warning

Dynamic Licensing

Insufficient Credits

Dynamic Licensing has been disabled because there are no chart

credits remaining.

Warning

Dynamic Licensing

Low Credits

Dynamic Licensing has a low number of chart credits remaining.

Warning

Dynamic Licensing

Report Expired

Dynamic Licensing has been disabled because the Dynamic

Licensing report is past due.

Warning

Dynamic Licensing

Report Near Due

The Dynamic Licensing report is almost due. Charts must be

reported by {0}.

Warning

Early Course Change

Early course change alert issued based on wheel-over TTG.

Warning

Early Course Change

Early course change alert issued based on wheel-over TTG. The

operator messages will be inhibited until this alert is acknowledged.

Alarm

Engine Mass Based

Fuel Consumption

Rate Unusable

Sensor Engine Mass Based Fuel Consumption Rate Value Integrity

VisionMaster FT

Alarm or

Caution

Depending on

configuration

Engine Power Value

Unusable

Sensor Engine Power Value Integrity VisionMaster FT

Alarm or

Caution

Depending on

configuration

Engine Propulsion

Power Unusable

Sensor Engine Propulsion Power Integrity VisionMaster FT

Alarm or

Caution

Depending on

configuration

Engine RPM Unusable

Sensor Engine RPM Integrity VisionMaster FT

Alarm or

Caution

Depending on

configuration

Engine Speed Value

Unusable

Sensor Engine Speed Integrity VisionMaster FT

Alarm or

Caution

Depending on

configuration

Summary of Contents for Visionmaster FT ECDIS




















































































































































































































































































































































































































































































































































Search results

Summary of Contents for Visionmaster FT ECDIS

Reviews:

Related manuals for Visionmaster FT ECDIS

Brands by name

Popular brands

Sperry Marine Visionmaster FT ECDIS, User Manual

Search results

Summary of Contents for Visionmaster FT ECDIS

Reviews:

Related manuals for Visionmaster FT ECDIS

Brands by name

Popular brands