Sperry Marine Visionmaster FT ECDIS User Manual Download Page 79 | Manualshive

Page: 79 / 531

background image

ECDIS User Guide

Basic Operation of ECDIS

3-11

65900012

The Latitude/Longitude (L/L) readings are replaced by dashes if the
following happen:

•

the cursor passes over popup windows or toolbars

•

own ship’s position is lost

•

the compass is unaligned

•

there is a compass error.

Where the L/L and bearing data is acquired from a valid sensor data source
the values are displayed in green, if the position data is degraded then the
values are displayed in yellow, if the position data is considered invalid and
unusable the data is shown in yellowish-orange. For further information on
sensor data sources see Sensors Menu.

«
...
77
78
79
80
81
...
»

Summary of Contents for Visionmaster FT ECDIS




















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Visionmaster FT ECDIS

Brand: Navman Pages: 20

Brand: Navman Pages: 70

Marine Rescue GPS

Brand: Nautilus Lifeline Pages: 9

Brand: Holux Pages: 3

Brand: Garmin Pages: 8

Brand: Garmin Pages: 78

Brand: YF Pages: 18

Brand: Garmin Pages: 2

Brand: soloprotect Pages: 9

Brand: Tractive Pages: 54

Brand: Leica Geosystems Pages: 74

Brand: Kogan Pages: 19

Brand: Dakwit Pages: 12

Brand: Elite Pages: 56

Brand: Kannad Pages: 48

Brand: SQUANTO Pages: 10

Brand: AIS COMAR SYSTEMS Pages: 20

Brand: I-Trac Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands