Sperry Marine Visionmaster FT ECDIS User Manual Download Page 44

Page: 44 / 531

Basic Operation of ECDIS

ECDIS User Guide

2-2

65900012

System Controls

The operator controls the VisionMaster FT system via a control panel
assembly, monitor controls and a power On/Off switch.

Control Panel

The Control Panel consists of the following group of controls:



Trackball assembly



Rotary controls



Adjustment and Acknowledgement buttons.

Summary of Contents for Visionmaster FT ECDIS




















































































































































































































































































































































































































































































































































Search results

Summary of Contents for Visionmaster FT ECDIS

Reviews:

Related manuals for Visionmaster FT ECDIS

Brands by name

Popular brands

Sperry Marine Visionmaster FT ECDIS, User Manual

Search results

Summary of Contents for Visionmaster FT ECDIS

Reviews:

Related manuals for Visionmaster FT ECDIS

Brands by name

Popular brands