Sperry Marine Visionmaster FT ECDIS User Manual Download Page 314

Page: 314 / 531

Alerts

ECDIS User Guide

7-16

65900012

Alert Type

Description

Priority

Notes

AIS Full

The number of AIS targets exceeds system capacity (maximum

250). AIS targets that are furthest away are not displayed.

Warning

AIS Interface Failure

An interface with the AIS unit has failed

Warning

AIS MMSI Mismatch

Expected AIS transceiver MMSI {0}, actual VDO MMSI {1}

Warning

AIS: Integrity Error

Alarm generated by AIS hardware

Warning

App Version

Mismatch

Not all nodes running same version of application. Can cause

unpredictable system behaviour. Ensure that all nodes have the

same version installed, and restart the system.

Warning

Approaching Route

End

Approaching the end of the route.

Alarm or

Warning

Depending on

configuration

Approaching

Waypoint

Approaching a waypoint on the external route.

Alarm or

Warning

Depending on

configuration

ARCS Skipper Not

Supported

System detects ARCS Skipper permits installed. Only ARCS

Navigator permits are supported for operation with ARCS RNC

charts.

Warning

Area With Special

Conditions (ECDIS)

Crossing an area with special conditions on the chart along the

ship's present course.

Warning or

Caution

Depending on

configuration

Arrival Time Not

Achievable

System cannot generate speed orders for ship to arrive at desired

arrival time and are within the speed limits of the monitored route.

Warning

Attitude Unusable

Sensor Attitude Integrity VisionMaster FT

Alarm or

Caution

Depending on

configuration

Authorization Failure

System is Unauthorized

Warning

Autopilot

Communication Failed

Communication with the autopilot has failed. The system cannot

control the autopilot.

Alarm

Summary of Contents for Visionmaster FT ECDIS




















































































































































































































































































































































































































































































































































Search results

Summary of Contents for Visionmaster FT ECDIS

Reviews:

Related manuals for Visionmaster FT ECDIS

Brands by name

Popular brands

Sperry Marine Visionmaster FT ECDIS, User Manual

Search results

Summary of Contents for Visionmaster FT ECDIS

Reviews:

Related manuals for Visionmaster FT ECDIS

Brands by name

Popular brands