Sony CXD5602 User Manual Download Page 1005

Page: 1005 / 1010

CXD5602 User Manual

－

1005/1010

－

HPADC

High Performance A/D

Converter

The HPADC is the A/D Converter in the CXD5602.

HOST I/F

HOST Interface

The HOST I/F is the format to communicate with the external HOST CPU.

Local AHB

---

The Local AHB is the matrix bus which connects the System and I/O Processor

with the SYS SRAM and the SYSTEM Bus.

LPADC

Low Power A/D Converter

The LPADC is the A/D Converter in the CXD5602.

NVIC

Nested Vectored

Interrupt Controller

For the NVIC, refer to the following URL.

http://infocenter.arm.com/help/topic/com.arm.doc.ddi0337e/Cihcffda.html

PMIC

Power Management IC

The PMIC is the IC to control power supply. As a companion chip for the

CXD5602, the CXD5247 is prepared. In this document, the CXD5247 is assumed

as the PMIC.

PMU

Power Management Unit

The PMU is the block that performs overall power supply control of the

CXD5602.

Refer to Chapter 3.4.

POR

Power On Reset

The POR is the reset that is enabled when power is supplied.

RCOSC

---

The RCOSC is the internal oscillator block.

Refer to Section 3.5.3.1.

Radio Frequency

The RF is the frequency band of the GNSS signal.

RTC

Real Time Clock

For the RTC, refer to Chapter 3.6

SCU

Sensor Domain

The SCU is the block which is equipped with the HPADC, LPADC, and the

interface to the external sensors. Please check

エラー

参照元が見つかりませ

ん。

. For details, refer to Chapter 3.9.

Sleep

---

Sleep is the status that any of the power domains of the CXD5602 becomes OFF,

or any of the DSPs belonging to the power domains is not in operation.

SYSCPU

System and I/O Processor

The SYSCPU contains Cortex

-M0+, Interrupt input register, Timer, WDT,

SLEEPING signal monitor, and Debug function (ITM).

The Tile address converter and the memory protection unit are equipped outside

the SYSCPU.

(Refer to

エラー

参照元が見つかりません。

)

SYSIOP

System and IOP Domain

The SYSIOP is the functional block equipped with one Cortex

-M0+, to perform

a variety of controls of the CXD5602, indicated in

エラー

参照元が見つかり

ません。

. Refer to Section 2.5.2 as well.

SYSPLL

---

The SYSPLL is the internal PLL. Refer to Section 3.5.3.3.

SYSTEM Bus

---

The SYSTEM Bus is the BUS inside the SYSIOP.

Refer to

エラー

参照元が見つかりません。

SYS SRAM

---

The SYS SRAM is 256 KByte of SRAM inside the System and IOP Domain.

Wakeup

Wakeup is the status that the power domains of the CXD5602 becomes ON, or

the DSPs belonging to the power domains starts operations.

«
...
1003
1004
1005
1006
1007
...
»

Summary of Contents for CXD5602



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CXD5602

Reviews:

Related manuals for CXD5602

Brands by name

Popular brands

Sony CXD5602, User Manual

Search results

Summary of Contents for CXD5602

Reviews:

Related manuals for CXD5602

Brands by name

Popular brands