Sony CXD5602 User Manual Download Page 43

Page: 43 / 1010

CXD5602 User Manual

－

43/1010

－

2.6.3

System Memory

There is 256 KByte SRAM in total which is connected to the AHB of the System and I/O Processor.

The SRAM block is made up of four 64K Byte Logic Tiles. One tile of the four is divided into four sub Logic

Tiles of: 8 KByte, 8 KByte, 16 KByte, and 32 KByte.

Each Logic Tile has the AHB I/F individually. The application program can access data from each Logic Tile via

local AHB. In addition, the Logic Tile is the unit for the SRAM access protection function. You can use

protection feature that keeps masters with specific Master ID from accessing specific SRAM Logic Tiles. The

protection feature can be controlled via buses. You can assign only Arm

Cortex

-M0+ of SYSCPU as master

that can control the protection feature. Shortly after the POR, all masters can access all Logic Tiles.

Power domain is PWD_CORE. When PWD_CORE is turned OFF, this memory cannot be used. Each sub area

tile is allocated to serial addresses; therefore, each sub Logic Tile can be turned ON/OFF individually. There are

two operation modes for the SRAM power-off: Retention mode and Shutdown mode. They can be set by system

control registers.

2.6.4

Backup Memory

There is 64 KByte SRAM in total which is connected to the AHB in System and IOP Domain for backup.

You can use protection feature that keeps masters with specific Master ID from accessing specific SRAM Logic

Tiles. The protection feature can be controlled via buses.

Power domain belongs to PWD_PMU area. You can use protection feature that keeps masters with specific

Master ID from accessing specific SRAM Logic Tiles. The protection feature can be controlled via buses. Power

ON/OFF can be controlled by registers. There are two operation modes for the SRAM power-off: Retention mode

and Shutdown mode. They can be set by system control registers.

2.7

Clock and Reset

2.7.1

Overview

The clock architecture inside the CXD5602 enables circuit blocks to select a variety of clock sources. It can

support wide range of application with optimized power consumption, from low speed sensing operation with low

power consumption, to high speed application processing using multi-core processor.

The CXD5602 has five types of usable clock sources and is made up of main five clock domains in accordance

Summary of Contents for CXD5602



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CXD5602

Reviews:

Related manuals for CXD5602

Brands by name

Popular brands

Sony CXD5602, User Manual

Search results

Summary of Contents for CXD5602

Reviews:

Related manuals for CXD5602

Brands by name

Popular brands