Sharp AR-BC260 Service Manual Download Page 169 | Manualshive

Page: 169 / 308

background image

AR-BC260 SIMULATION 9 - 31

3. Used to set the paper kind display mode in the manual paper

feed mode.

∗

Documents or paper of 8.5" x 13" are treated as a selectable
size.

(Selection item)

[Copy vendor mode]

1. Select the kind of the counter with the scroll key.

2. Enter "1" or "2" with the 10-key pad and press the [OK] key.

26

26

-2

Purpose

Setting

Function
(Purpose)

1. Used to set the paper size of the large capacity

tray. (When the paper size is changed, the
software setup must be changed accordingly
with this simulation.)

2. Used to detect 8.5 " x 13" (INCH Series) paper or

documents and to set the display mode. (All
paper feed modes)

3. Used to set the display form of the paper kind in

the manual paper feed mode.

Section

Paper feed

Item

Specifications

Operation/
Procedure

1. Used to set the paper size of the large capacity

tray.

2. Used to set to allow 8.5" x 13" size paper to be

treated as a selectable size.

Item

Set value

Content

Paper size
setting

LCC

1

8.5 x 11 (Default)

2

A4

LEGAL

0

8.5 x 14 (Default)

1

8.5 x 13

MFT TYPE

0

Displayed in gram.

1

Displayed in pound.

26

-3

Purpose

Setting

Function
(Purpose)

Used to set the auditor specification mode. Setting
must be made according to the use conditions of the
auditor.

Section

Auditor

Item

Specifications

Operation/
Procedure

Enter the code number corresponding to the auditor
specification mode.

Mode

Content

[P10]

Built-in auditor mode

[AR-EC1]

Card counter mode (only Japan)

[MODE1]

Coin vendor mode 1

[MODE2]

Coin vendor mode 2

[MODE3]

Coin vendor mode 3

Diag

setting

Specified

number

completed

with money

left

Lack of money during a

copy job

Specified

number

completed

with no

money left

BW/Color

(with no

money left)

Color (with

money left)

Case 1

Case 2

Case 3

Case 4

26-3=3

MODE1

Operation 1 Operation 2 Operation 2

Operation 1

26-3=4

MODE2

Operation 1 Operation 1 Operation 2

Operation 1

26-3=5

MODE3

Operation 1 Operation 3 Operation 2

Operation 3

Operation 1: The set status remains until the auto clear set

time has passed. (Default: 60sec Changeable
with key operations.)

Operation 2: Auto clear is not made.
Operation 3: Setting is immediately cleared, and the display

returns to the standby menu.

Case 1/Case 2 (with money left): B/W copy is allowed. If, however,
charge money fro color copy is exhausted during a color copy job,
when sufficient money for the job is supplied, only the color start
key of the READY lamp lights up.

26

-5

Purpose

Setting

Function
(Purpose)

Used to set the count mode of the total counter and
the maintenance counter.

Item

Specifications

Counter

Operation/
Procedure

Used to set the single count-up or double count-up
for the total counter, the maintenance counter, and
the developer counter when printing is performed
with A3, 11 x 17" paper.

Item

Content

Set range

Default

A

TOTAL(B/W)

Total counter (B/W)

1 – 2

2

B

TOTAL(COL)

Total counter (Color)

1 – 2

2

C

MAINTE(B/W)

Maintenance (B/W)

1 – 2

2

D

MAINTE(COL)

Maintenance (Color)

1 – 2

2

«
...
167
168
169
170
171
...
»

Summary of Contents for AR-BC260





















































































































































































































































































































Reviews:

No comments

Related manuals for AR-BC260

Brand: SPRT Pages: 28

imageRUNNER ADVANCE DX C478iZ

Brand: Canon Pages: 208

imageRUNNER ADVANCE DX C477iFZ

Brand: Canon Pages: 92

Brand: Oki Pages: 126

Brand: Oki Pages: 99

Brand: MF DIGITAL Pages: 2

WorkCentre Pro 32

Brand: Xerox Pages: 14

Brand: Magicard Pages: 108

Brand: Xerox Pages: 70

Brand: Oki Pages: 2

Brand: Keithley Pages: 97

Brand: Sagem Pages: 154

Brand: OmniPrint Pages: 23

Brand: Ricoh Pages: 678

Brand: POS Tablet Pages: 4

WorkCentre 5845

Brand: Xerox Pages: 14

WorkForce 610 Series

Brand: Epson Pages: 52

Brand: Epson Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands