manualshive.com logo in svg

Sharp AR-BC260, Service Manual

Share
Download
Sharp AR-BC260 Service Manual Download Page 201

AR-BC260  SIMULATION  9 - 63

1. Select the color to be set with the color keys (CMY).
2. The display page can be shifted with the scroll key.

(Display item)

(

D MULTI 

COUNT

Print quantity

1

999

1

E PAPER

Paper feed tray selection 
(MFT, CS1,CS2, CS3, 
CS4, LCC)

1

6

2

(CS1)

F EXIT TRAY Paper exit tray selection 

(R, S)

1

2

1  (R)

63

63

-01

Purpose

Adjustment/Setting/Operation data output, check 
(display, print)

Function 
(Purpose)

Used to check the result of shading correction. (The 
shading correction data are displayed.)

Section

Scanner (Exposure)

Item

Operation

Operation/
Procedure

Used to display the latest shading correction result.
Data for each color can be separately checked with 
the color keys.

GAIN ODD

Gain adjustment value (ODD)

1/5

GAIN EVEN

Gain adjustment value (EVEN)

OFFSET ODD

Offset value (ODD)

2/5

OFFSET EVEN

Offset value (EVEN)

SMP AVE ODD

Reference plate sampling average value 
(ODD)

3/5

SMP AVE EVEN

Reference plate sampling average value 
(EVEN)

TARGET VALUE Target value

4/5

BLACK LEVEL

Black output level 

ERR CODE

Error code (0, 1-4, 11-14)
0: No error
1: STAGE 1, exceeded number of loops
2: STAGE 2, the target value is less 

than the specified level.

3: STAGE 3, the gain set value is 

negative.

4: END is not asserted.

∗

Add +1- to the error code in color 
mode.

4/5

RSPF WHITE 
LEVEL 1ST

White reference level of the document 
feeder unit in the first scanning

5/5

RSPF WHITE 
LEVEL 2nd

White reference level of the document 
feeder unit in the second scanning

Display

Content

Min. 

Value

Max. 

Value

Default

63

-03

Purpose

Adjustment

Function 
(Purpose)

Used to adjust the CCD color balance (gamma).

Section

Scanner (reading)

Item

Picture quality

Color balance

Operation/
Procedure

Set the SIT chart (UKOG-0280FCZZ) on the 
document table, and press the [EXECUTE] key. The 
color coefficient automatic adjustment pattern 
reading is started to calculate and display the color 
coefficient data.
The color coefficient data of each color can be 
displayed with the color key.

63

-05

Purpose

Setting

Function 
(Purpose)

Used to set the CCD color balance (gamma) default.

Section

Scanner (reading)

Item

Picture quality

Color balance

Operation/
Procedure

1. Press the [EXECUTE] key, and the [YES] and 

[NO] keys become active.

2. When the [YES] key is pressed, the CCD color 

balance value is set to the default.

63

-06

Purpose

Adjustment/Operation data output check (display, 
print)

Function 
(Purpose)

Used to check the color balance (gamma) check 
patch. 

Section

Image process (ICU)

Item

Picture quality

Color balance

Operation/
Procedure

1. Set the color balance check patch printed with 

SIM 46-21 on the document table. 

2. Press the [EXECUTE] key, and the reading is 

started and the data are displayed on the display.

Summary of Contents for AR-BC260





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands