manualshive.com logo in svg

Sharp AR-BC260, Service Manual

The Sharp AR-BC260 is a versatile printer that offers high-quality output. To easily set it up and begin printing, make sure to download the free Installation Manual from our website. This comprehensive manual provides step-by-step instructions and is available for instant download at manualshive.com.

Share
Download
background image

AR-BC260  SETTING AND ADJUSTMENTS  8 - 37

3) Place A3 (11 x 17) document on the document table and press

the [EXECUTE] key.

This adjustment must be performed in the following cases:

• When the manual paper feed tray section is disassembled.

• When the manual paper feed tray unit is replaced.

• When a U2 trouble occurs.

• When the PCU PWB is replaced.

• When the EEPROM of the PCU PWB is replaced.

1) Enter the SIM 40-2 mode.

2) Set the manual paper feed guide to the maximum position.

3) Press the [EXECUTE] key.

The [EXECUTE] key is highlighted. Then it returns to the nor-
mal display. The manual paper feed guide maximum width
position detection level is recognized.

4) Set the manual paper feed guide to A4 (11 x 8.5") size width.

5) Press the [EXECUTE] key.

The [EXECUTE] key is highlighted. Then it returns to the nor-
mal display. The manual paper feed guide A4 (11 x 8.5") width
position detection level is recognized.

6) Set the manual paper feed guide to A4R (11 x 8.5"R) size

width.

7) Press the [EXECUTE] key.

The [EXECUTE] key is highlighted. Then it returns to the nor-
mal display. The manual paper feed guide A4R (11 x 8.5" R)
width position detection level is recognized.

8) Set the manual paper feed guide to the minimum position.

9) Press the [EXECUTE] key.

The [EXECUTE] key is highlighted. Then it returns to the nor-
mal display. The manual paper feed guide minimum width
position detection level is recognized.

If the above procedure is not completed normally, "ERROR" is
highlighted. If the above procedure is completed normally, the
above data are stored and "COMPLETE" is highlighted.

This adjustment must be performed in the following cases:

• When the operation panel is replaced.

• When a U2 trouble occurs.

• When the MFP PWB is replaced.

• When the EEPROM of the MFP PWB is replaced.

1) Enter the SIM 65-1 mode.

2) Touch the four cross marks on the display precisely.

When the cross marks are pressed, the buzzer sounds and
they are changed from black display into gray display. When
the touch panel adjustment is completed by pressing all the
four marks, the display returns to the simulation sub code
number entry menu.

If there is any abnormality, the first display is shown again.

When pressing the touch panel key, check that there is no
shift between the display frame and the detection position.

∗

When touching the crosses, never use a needle or a pin with a
sharp point.

This adjustment must be performed in the following cases:

• When a part in the DC power unit is replaced.

ADJ 15

Manual paper feed tray paper 
size sensor adjustment

A6

A5

A5

A4

A4

A3

A3W

B5

B5

B4

5

1

/

2

7

1

/

4

11

12

8

1

/

2

A6

A5

A5

A4

A4

A3

A3W

B5

B5

B4

5

1

/

2

7

1

/

4

11

12

8

1

/

2

ADJ 16

Touch panel coordinates 
setting

ADJ 17

Power voltage adjustment

VR701

VR702

Summary of Contents for AR-BC260





















































































































































































































































































































Reviews:

No comments

Related manuals for AR-BC260

DataCard CP60 Quick Install Manual preview
CP60
Brand: DataCard Pages: 8
Oki C910 Hardware preview
C910
Brand: Oki Pages: 2
Oki C910 Material Safety Data Sheet preview
C910
Brand: Oki Pages: 52
Oki C110 Manual Do Usuário preview
C110
Brand: Oki Pages: 117
Oki C110 How To Remove Jammed Paper preview
C110
Brand: Oki Pages: 45
Oki C110 Manual De L'Utilisateur preview
C110
Brand: Oki Pages: 112
Oki C110 Guías Del Usuario Manual preview
C110
Brand: Oki Pages: 115
Oki C110 Quick Setup preview
C110
Brand: Oki Pages: 2
DataCard SP35 Plus Quick Install Manual preview
SP35 Plus
Brand: DataCard Pages: 8
DataCard Datacard SP35 Quick Install Manual preview
Datacard SP35
Brand: DataCard Pages: 8
DataCard SD Series Packaging Manual preview
SD Series
Brand: DataCard Pages: 3
Xerox 665 User Manual preview
665
Brand: Xerox Pages: 89
Océ VarioPrint 1055 User Manual preview
VarioPrint 1055
Brand: Océ Pages: 194
Oce CS9360 Installation Manual preview
CS9360
Brand: Oce Pages: 12
Samsung Xpress M2020W User Manual preview
Xpress M2020W
Brand: Samsung Pages: 199
Copystar CS 5551ci Specifications preview
CS 5551ci
Brand: Copystar Pages: 4
Olivetti d-Color MF280 Functions preview
d-Color MF280
Brand: Olivetti Pages: 74
Jolimark DP550 User Manual preview
DP550
Brand: Jolimark Pages: 64

Brands by name

Popular brands

Load more brands