Sharp AR-BC260 Service Manual Download Page 287

Page: 287 / 308

AR-BC260 ELECTRIC DIAGRAM 13 - 19

DPEDx

Paper empty sensor

Detects paper presence on the paper tray.

AR-D17N/
AR-D18N/
AR-D19N

DPFCx

Paper feed clutch

Controls ON/OFF of the paper feed roller.

AR-D17N/
AR-D18N/
AR-D19N

DPFSx

Pickup solenoid

Presses the paper pickup roller onto paper.

AR-D17N/
AR-D18N/
AR-D19N

DPPD1

Paper transport sensor 1

Detects paper transport.

AR-D17N/
AR-D18N/
AR-D19N

DPPD2

Paper transport sensor 2

Detects paper transport.

AR-D17N/
AR-D18N

DPPD3

Paper transport sensor 3

Detects paper transport.

AR-D17N/
AR-D18N

DSWF

Front door open detection

Detects opening of the front door.

AR-BC260

DSWL

Paper exit door open detection

Detects opening of the paper exit door.

AR-BC260

DSWR

Paper feed door open detection

Detects opening of the paper feed door.

AR-BC260

DUSTPTR

Punch dust full sensor

Detects punch dust full.

AR-F13

DTRC

Transport clutch

Controls ON/OFF of the transport roller.

AR-D17N/
AR-D18N/
AR-D19N

ES Entry

port

sensor

AR-F13

FAM

Bundle exit sensor

AR-F13

FDS

Front door sensor

AR-F13

FDSW

Front door switch

AR-F13

FE Bookbinding

clock

sensor

AR-F13

FES

Bookbinding paper senor

AR-F13

FFJM

Alignment motor (F)

AR-F13

FFM Transport

motor

AR-F13

FFSM

Stapler/Folding motor staple operation/
Paper folding operation

AR-F13

FHPS

Bookbinding HP sensor

AR-F13

FJHPS Alignment

sensor

AR-F13

FLM Shift

motor

AR-F13

FPM

Paddle motor oscillation guide drive,
discharge to offset tray

AR-F13

FPNM Punch

motor

AR-F13

FPS Bookbinding

position

sensor

AR-F13

FPSM

Puncher side registration motor

AR-F13

FRHPS

Bookbinding roller HP sensor

AR-F13

FRJM

Alignment motor (R)

AR-F13

FSM

Slide motor staple unit shift

AR-F13

FUSM

Fusing drive motor

Drives the fusing unit.

AR-BC260

GSS

Face up/down switch gate solenoid

Drives the face-up/down switch gate.

AR-BC260

HLTS1

Upper heat roller thermostat

Detects an abnormally high temperature to turn off the heater
lamp.

AR-BC260

HLTS2

Lower heat roller thermostat

Detects an abnormally high temperature to turn off the heater
lamp.

AR-BC260

HPOS

Offset home position sensor

Detects the offset home position.

AR-BC260

HUD

Humidity sensor

Detects the humidity.

AR-BC260

Joint switch

AR-F13

Document length detection SW (Short)

Detects the document length on the tray.

AR-BC260
(RSPF)

Document length detection SW (Long)

Detects the document length on the tray.

AR-BC260
(RSPF)

Lift lock sensor

AR-F13

LEDONx

Paper size sensor

Detects the paper size.

AR-F13

LLLS

Lift lower limit sensor

AR-F13

LUD1

1 cassette lift-up upper limit detection

Detects the paper upper limit position.

AR-BC260

LUM1

1 cassette lift-up motor

Drives the lift plate.

AR-BC260

MHPS

Mirror home position sensor

Detects the scanner home position.

AR-BC260

MPED

Manual feed paper empty sensor

Detects paper presence on the paper tray.

AR-BC260

MPFC

Manual paper feed clutch

Controls ON/OFF of the paper feed roller. Presses the paper
pickup roller onto paper.

AR-BC260

Signal name

Name

Function/Operation

Section

Summary of Contents for AR-BC260





















































































































































































































































































































Search results

Summary of Contents for AR-BC260

Reviews:

Brands by name

Popular brands

Sharp AR-BC260, Service Manual

Search results

Summary of Contents for AR-BC260

Reviews:

Brands by name

Popular brands