manualshive.com logo in svg

Sharp AR-BC260, Service Manual

Share
Download
Sharp AR-BC260 Service Manual Download Page 189

AR-BC260  SIMULATION  9 - 51

(Items to be set)

When tone gap occurs in the high density area in the photo copy 
mode, set this function to ENABLE, and the max. density level will 
fall, reducing tone gap.

2. Set the color patch image printed in procedure 1 on the 

document table.

3. Press the FACTORY key on the operation panel, and press the 

[EXECUTE] key.
The copy color balance adjustment (step 1) is automatically 
performed and the color balance check patch image is printed.

4. Press the REPEAT key on the operation panel.
5. Press the [EXECUTE] key.

The color patch image (adjustment pattern) is printed.

6. Set the color patch image (adjustment pattern) printed in 

procedure 5 on the document table. (Place the darker patch on 
the left side.)

7. Press the FACTORY key on the operation panel, and press the 

[EXECUTE] key.
The copy color balance adjustment (step 2) is automatically 
performed and the color balance check patch image is printed.

8. Press the [OK] key on the operation panel.
The initial setting of the half-tone image correction is performed 
according to this adjustment data.

2. Select the adjustment point with the scroll key.
3. Enter the adjustment value of the selected point with the 10-

key and press the [OK] key. (The entered value is set.)

(Items to be set)

2. Press the [YES] key, and the copy color balance is set to the 

default. (Press the [NO] key to cancel.)

(Standard value reset items)

1. RED setup ratio

2. GREEN setup ratio

3. BLUE setup ratio

4. YELLOW setup ratio

5. MAGENTA setup ratio

6. CYAN setup ratio

Display

Min. 

Value

Max. 

Value

Default

A

POINT1

245

755

500

↓

↓

↓

↓

↓

O

POINT15

245

755

500

46

-23

Purpose

Setting

Function 
(Purpose)

Used to set Enable/Disable of half-tone high-density 
correction.

Item

Picture quality

Color balance

Operation/
Procedure

[ENABLE]: Correction is enabled.
[DISABLE]: Correction is disabled.
Default set: DISABLE

46

-24

Purpose

Adjustment

Function 
(Purpose)

Used to adjust the copy color balance automatically. 
(All color copy mode gamma/density adjustment)

Item

Picture quality

Color balance

Operation/
Procedure

1. Press the [EXECUTE] key. (A3 or 11 x 17 paper 

is automatically selected.) The color patch image 
(adjustment pattern) is printed.

46

-25

Purpose

Adjustment

Function 
(Purpose)

Used to adjust copy color balance (Single color 
mode)

Section

Image process (ICU)

Item

Picture quality

Color balance

Operation/
Procedure

1. Select the color to be adjusted with the color key 

(C/M/Y).

Display

Min. 

Value

Max. 

Value

Default

C

M

Y

A

RED

0

255

0

255

255

B

GREEN

0

255

255

0

255

C

BLUE

0

255

255

255

0

D

YELLOW

0

255

0

0

255

E

MAGENTA

0

255

0

255

0

F

CYAN

0

255

255

0

0

46

-26

Purpose

Adjustment

Function 
(Purpose)

Used to set the copy color balance adjustment to the 
default. (Single color copy mode)

Section

Image process (ICU)

Item

Picture quality

Color balance

Operation/
Procedure

1. Press the [EXECUTE] key. (YES/NO keys are 

displayed.)

Summary of Contents for AR-BC260





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands