Sharp AR-BC260, Service Manual

Page: 153 / 308

AR-BC260 SIMULATION 9 - 15
(Sensors to be detected)
During the operation of the load, the [EXECUTE] key is
highlighted. If the [EXECUTE] key is pressed while it is
highlighted, the operation is stopped.
(Loads to be selected)
3 -10
Purpose Operation test/check
Function
(Purpose) Used to adjust the sections in the finisher.
Section Finisher
Item Operation
Operation/
Procedure 1. Select the adjustment item with the scroll key.
2. Enter the adjustment value with the 1o-key and
press the OK key to set the value.
Item
Set
range
Initial
value
A Saddle binding position adjustment 0 – 400 200
B Saddle folding position adjustment 0 – 400 200
C Front alignment position adjustment 0 – 20 10
D Rear alignment position adjustment 0 – 20 10
E Staple rear one-point binding position
adjustment 0 – 200 100
F Staple front one-point binding position
adjustment 0 – 200 100
G Staple two-point binding center
adjustment
0 – 200 100
H Staple two-point binding pitch adjustment 0 – 100 50
I Punch center adjustment 47 – 53 50
J Punch hole position adjustment 0 – 100 50
4
4 -2
Purpose Operation test/check
Function
(Purpose) Used to check the operations of the desk/large
capacity tray sensors and detectors and the related
circuits.
Section Paper feed
Item Operation
Operation/
Procedure The operating conditions of the sensors and
detectors in the paper feed section are displayed.
The active sensors and detectors are highlighted.
DLUD1 Desk 1cs upper limit detection
DLUD2 Desk 2cs upper limit detection
DLUD3 Desk 3cs upper limit detection
DPED1 Desk 1cs paper empty detector
DPED2 Desk 2cs paper empty detection
DPED3 Desk 3cs paper empty detection
DCSPS1 Desk 1cs remaining quantity detection
DCSPS2 Desk 2cs remaining quantity detection
DCSPS3 Desk 3cs remaining quantity detection
DPPD1 Desk paper transport detection 1
DPPD2 Desk paper transport detection 2
DPPD3 Desk paper transport detection 3
DLUID1 Desk 1cs lift unit installation detection
DLUID2 Desk 2cs lift unit installation detection
DLUID3 Desk 3cs lift unit installation detection
DDOPD Desk door open detection
DCSS11 Desk 1cs paper size detection 1
DCSS12 Desk 1cs paper size detection 2
DCSS13 Desk 1cs paper size detection 3
DCSS14 Desk 1cs paper size detection 4
DCSS21 Desk 2cs paper size detection 1
DCSS22 Desk 2cs paper size detection 2
DCSS23 Desk 2cs paper size detection 3
DCSS24 Desk 2cs paper size detection 4
DCSS31 Desk 3cs paper size detection 1
DCSS32 Desk 3cs paper size detection 2
DCSS33 Desk 3cs paper size detection 3
DCSS34 Desk 3cs paper size detection 4
LTD Transport sensor
LUD LCC upper limit detection
LLD LCC lower limit detection
LPED LCC paper empty detection
LTOD LCC main unit connection detection
LCD LCC tray insertion detection
LOSW LCC upper open/close detection SW
LRE LCC lift motor encoder
24V LCC24V detection
LLSW LCC upper limit SW
4 -3
Purpose Operation test/check
Function
(Purpose) Used to check the operations of the desk/large
capacity tray loads and the control circuit.
/
Section Paper feed
Item Operation
Operation/
Procedure 1. The names of the loads that can be checked are
displayed. Select a load to be checked with the
key, and the selected load is highlighted.
2. Press the [EXECUTE] key. The load selected in
procedure 1 starts the operation.
DM Desk transport motor
DLM1 Desk 1cs lift-up motor
DLM2 Desk 2cs lift-up motor
DLM3 Desk 3cs lift-up motor
DPFC1 Desk 1cs paper feed clutch
DPFC2 Desk 2cs paper feed clutch
DPFC3 Desk 3cs paper feed clutch
DTRC Desk transport clutch
DPFS1 Desk 1cs paper feed solenoid
DPFS2 Desk 2cs paper feed solenoid
DPFS3 Desk 3cs paper feed solenoid
LTM LCC transport motor
LLM LCC lift motor operation
LPFCL LCC paper feed clutch
LPSL LCC paper feed solenoid
LTCL LCC transport clutch
LTLSL LCC tray lock solenoid