manualshive.com logo in svg

Sharp AR-BC260, Service Manual

Share
Download
Sharp AR-BC260 Service Manual Download Page 151

AR-BC260  SIMULATION  9 - 13

C. Details

Scanning is performed at the magnification ratio set in procedure 1 
is executed.

During scanning, the [EXECUTE] key is highlighted. If the 
[EXECUTE] key is pressed under this state, the operation is 
interrupted.

After completion of scanning, the [EXECUTE] key returns to the 
normal display.

To resume scanning, start with procedure 2. To change the 
magnification ratio, start with procedure 1.

Scanning is performed at the max. scanning length (432 mm). If, 
however, the magnification ratio is set to a value greater than 
100% in procedure 1, the scanning length is changed accordingly.

The active sensors and detectors are highlighted.

• The light source unit is at the home position. a MHPS is 

highlighted.

• The light source unit is not at the home position. a MHPS is 

displayed normally.

Scanning is repeatedly performed until the [EXECUTE] key or the 
interruption key is pressed.

[When the RSPF is installed]

1

1

-1

Purpose

Operation test/check

Function 
(Purpose)

Used to check the operations of the scanner unit and 
its control circuit.

Section

Scanner (reading)

Item

Operation

Operation/
Procedure

1. Select the copy (scanning) magnification ratio 

with the zoom key. The magnification ratio can 
be increased or decreased with the [ZOOM] key 
by the increment of 1%. The selected 
magnification ratio is displayed on the 
magnification ratio display.

2. Press the [EXECUTE] key.

1

-2

Purpose

Operation test/check

Function 
(Purpose)

Used to check the sensors and detectors in the 
scanner section and the related circuits.

Section

Scanner (reading)

Item

Operation

Operation/
Procedure

The operations of sensors and detectors in the 
scanner section are displayed.

1

-5

Purpose

Operation test/check

Function 
(Purpose)

Used to check the scanner (scanning) unit and its 
control circuit.

Section

Scanner (reading)

Item

Operation

Operation/
Procedure

1. Select the copy (scanning) magnification ratio 

with the key (touch panel).  The magnification 
ratio can be increased or decreased with the 
[ZOOM] key by the increment of 1%.
The selected magnification ratio is displayed on 
the magnification ratio display.

2. Select the scan mode (Color / B/W). 
3. Press the [EXECUTE] key.

Scanning is repeated under the conditions set in 
procedures 1 and 2.
During scanning, the [EXECUTE] key is 
highlighted. 

2

2

-2

Purpose

Operation test/check

Function 
(Purpose)

Used to check the operations of the sensors and 
detectors in the document feeder unit and their 
related circuits. 

Section

Automatic document feeder

Item

Operation

Operation/
Procedure

The operating status of the sensors and detectors in 
the document feeder unit is displayed.  
The active sensors and detectors are highlighted.

W0

Document set sensor

PAPER

Document transport sensor

COVER 
OPEN

Unit (OC cover) open/close sensor

PO

Paper exit sensor

COVER

Paper feed cover open/close sensor

L1

Document length sensor 1

L2

Document length sensor 2

W1

Document width sensor (small)

W2

Document width sensor (middle)

W3

Document width sensor (large)

Summary of Contents for AR-BC260





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands