manualshive.com logo in svg

Sharp AR-BC260, Service Manual

Share
Download
Sharp AR-BC260 Service Manual Download Page 115

AR-BC260  SETTING AND ADJUSTMENTS  8 - 22

The following functions (HV/HT/TC/RRM/MD) of SIM 44-1 must be set to Enable.

(Adjustment items which affect the copy color balance/density but need not to be adjusted frequently. When, 
however, a trouble occurs, check and adjustment must be made.)

1) Adjustment item: ADJ 1, ADJ 7, ADJ 12, ADJ 13

(Relationship between the service contents and the copy color balance/density adjustment)

Note that procedures before and after the copy color balance/density adjustment differ depending on the machine status and the servicing
job contents.

Perform proper procedures according to the flow of the copy color balance/density adjustment.

There are following five major cases:

1) When installing

2) When periodic maintenance

3) When consumable part is replaced in repair work

4) When consumable part is not replaced in repair/checking work

5) Other repair/check

Item

Setting

Phenomenon when set to Disable

HV

Image forming section 
correction (process 
correction) (High-density 
image density correction)

ENABLE

The developing bias voltage correction 
and the main charger grid voltage 
correction are not performed.

Insufficient image density, background 
coy, improper color balance

HT

Half-tone image density 
correction

ENABLE

The half-tone image density correction 
is not performed.

Improper half-tone image density, 
background copy, improper color 
balance, tone jump

HT (PRT)

Half-tone image density 
correction (Printer)

ENABLE

The half-tone image density correction 
is not performed.

Improper half-tone image density, 
background copy, improper color 
balance, tone jump

TC

Transfer output correction

ENABLE

Correction of change due to humidity 
and correction of the transfer voltage 
are not performed.

Half-ton image section roughness, 
improper image density, insufficient 
density inside of image outlines

RRM

RRM speed correction

ENABLE

Correction of change due to humidity 
and correction of the rotate speed are 
not performed.

Improper color balance, roughness, 
background coy, toner dispersion, 
improper image density, image 
deflection, image flow, image dirt

MD

Photoconductor membrane 
decrease (sensitivity/
potential) correction

ENABLE

Correction of use frequency (sensitivity 
change) of OPC drum is not performed. 
(Main charger grid voltage correction)

Improper image density, background 
copy

MD 
(PRT_BK)

Photoconductor membrane 
decrease (sensitivity/
potential) correction 
(Printer: monochrome)

ENABLE

Correction of use frequency (sensitivity 
change) of OPC drum is not performed. 
(Main charger grid voltage correction)

Improper image density, background 
copy

AR

Image registration 
automatic adjustment

Does not affect during image quality 
adjustment.

AR CHK

YES/NO of error judgment 
in image registration 
automatic adjustment

Does not affect during image quality 
adjustment.

JOB No

ADJUSTMENT ITEM LIST

SIMULATION

ADJ 1

High voltage adjustment

ADJ 1A Main charger grid voltage adjustment

8-2

ADJ 1B DV bias voltage adjustment

8-1

ADJ 1C Transfer voltage adjustment

8-6

ADJ 7

Copy image focus (main scanning direction copy magnification ratio) adjustment (CCD unit position adjustment)

48-1

ADJ 12 Fusing pressure adjustment

ADJ 13 Fusing paper guide position adjustment

Summary of Contents for AR-BC260





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands