Sharp AR-BC260 Service Manual Download Page 70

Page: 70 / 308

AR-BC260 DESCRIPTIONS OF EACH SECTION 7 - 33

d. Paper resist section

The resist roller controls the relative position of the transported
paper and the transfer image.

The resist roller is driven by the resist roller motor.

The relative position of paper and the transfer image is determined
by the ON timing of the resist roller motor.

e. Others

∗

The paper transport section is provided with two paper detec-
tors, which perform the following functions:

1) Paper jam detection

2) Output of the reference signal for the operating timing of each

load

B. Disassembly/assembly/maintenance

(1) Paper feed/transport sections maintenance target parts

: Check (Clean, replace, or adjust as necessary.)

❍

: Clean

▲

: Replace

∆

: Adjust

✩

: Lubricate

❏

: Shift position

Upper resist roller

Lower resist roller

PS motor

Unit name

No.

Part name

When

calling

50K

100K 150K 200K 250K 300K 350K 400K

Remark

Paper feed
section

Cassette section
paper feed rollers

❍

Replace according to the
counter of each paper
feed port or within 2 years.

Torque limiter

Manual feed section
paper feed rollers

❍

Replace according to the
counter of each paper
feed port or within 2 years.

Torque limiter

Transport
section

Transport rollers

❍

Transport paper guide

❍

Summary of Contents for AR-BC260





















































































































































































































































































































Search results

Summary of Contents for AR-BC260

Reviews:

Brands by name

Popular brands

Sharp AR-BC260, Service Manual

Search results

Summary of Contents for AR-BC260

Reviews:

Brands by name

Popular brands