manualshive.com logo in svg

Sharp AR-BC260, Service Manual

Share
Download
Sharp AR-BC260 Service Manual Download Page 27

AR-BC260  EXTERNAL VIEW AND INTERNAL STRUCTURE  6 - 1

[6] EXTERNAL VIEW AND INTERNAL STRUCTURE

1. Name and function of each section

A. External view

No.

Parts

Note

Name

Function

1

Left tray

Finished sheets are deposited here.

2

Left side cover

Open this cover when a paper misfeed occurs in the fusing unit or the transfer 
unit.

3

Reversing single pass feeder

This automatically feeds originals to be scanned.
The feeder can turn the original over and scan the back side as well as the front 
side for support of two-sided originals.

4

Power switch

Press to turn power on and off.

5

Front cover

Open to replace toner cartridge.

6

Operation panel

Performs various functions with the operation keys and the touch panel. 

7

Centre tray

Finished sheets are deposited here.

8

Bypass tray

Special papers (including transparency film) and copy paper can be fed from the 
bypass tray.

9

Stand/1 x 500 sheet paper 
drawer

This stand has one paper tray. It can hold approximately 500 sheets of the 
recommended paper for color (80 g/m

2

 or 21 lbs.), or approximately 550 sheets of 

SHARP standard paper (64 g/m

2

 or 21 lbs.).

Option
(AR-D17N)

10

Stand/3 x 500 sheet paper 
drawer

This stand has three paper trays. Each tray can hold approximately 500 sheets of 
the recommended paper for color (80 g/m

2

 or 21 lbs.), or approximately 550 

sheets of SHARP standard paper (64 g/m

2

 or 21 lbs.).

Option 
(AR-D18N)

11

Duplex module/2 x 500 sheet 
paper drawer

This stand includes a module for automatic two-sided printing and two paper 
trays. The two trays can hold approximately 500 sheets of the recommended 
paper for color (80 g/m

2

 or 21 lbs.), or approximately 550 sheets of SHARP 

standard paper (64 g/m

2

 or 21 lbs.). To perform two-sided printing, a duplex 

bypass/inverter unit (AR-RB1) is required.

Option 
(AR-D19N)

12

Paper tray

Each tray can hold approximately 500 sheets of the recommended paper for color 
(80 g/m

2

 or 21 lbs.), or approximately 550 sheets of SHARP standard paper (64 

g/m

2

 or 21 lbs.).

13

Left side cover release

Push this release up to open the left side cover.

14

Duplex bypass/inverter unit

This module is required to automatically turn paper over within the machine for 
automatic two-sided printing.

Option 
(AR-RB1)

Without the duplex 
bypass/inverter unit
(14) installed.

1

2

3

4

14

13 12

11

5

6

7

8

9

10

Summary of Contents for AR-BC260





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands