manualshive.com logo in svg

Sharp AR-BC260, Service Manual

The Sharp AR-BC260 is a versatile printer that offers high-quality output. To easily set it up and begin printing, make sure to download the free Installation Manual from our website. This comprehensive manual provides step-by-step instructions and is available for instant download at manualshive.com.

Share
Download
background image

AR-BC260  ELECTRIC DIAGRAM  13 - 20

MPLD1

Manual paper length detection 1

Detects the paper length.

AR-BC260

MPLD2

Manual paper length detection 2

Detects the paper length.

AR-BC260

MPWS

Manual paper width detection 

Detects the paper width.

AR-BC260

MSW

Main switch 

Turns ON/OFF the main power.

AR-BC260

MTOP1

Manual tray pull-out detection 1

Detects the paper tray position.

AR-BC260

MTOP2

Manual tray pull-out detection 2

Detects the paper tray position.

AR-BC260

MTRC

Manual feed drive clutch 

Transmits drive power to the manual paper feed unit.

AR-BC260

OBHPS

Paper exit belt HP sensor

AR-F13

OCSW

O/G open sensor

Detects opening of the document cover. (Generates the 
document size detection timing signal.)

AR-BC260

OSM

Offset motor (Slide motor)

Drives the paper offset. 

AR-BC260

PAPER

Paper entry sensor

Detects presence of a document.

AR-BC260 
(RSPF)

PCFM

Process cooling fan motor

Exhaust and cools the process section. 

AR-BC260

PCS_C

Color toner concentration (process 
control) sensor

Detects the toner patch density (color toner) in image density 
correction.

AR-BC260

PE

Punch motor encoder

AR-F13

PED1

1 cassette paper empty detection

Detects paper presence on the paper tray.

AR-BC260

PFD1

1 cassette paper feed detection 

Detects paper delivery from No. 1 paper tray.

AR-BC260

PFM

Paper feed motor

Drives the paper feed section and the paper transport 
section.

AR-BC260

PHPS 

Paddle HP sensor

AR-F13

PO

Paper exit sensor

Detects presence of a document.

AR-BC260 
(RSPF)

POD1

Machine paper exit sensor 1

Detects discharged paper.

AR-BC260

POD2

Machine paper exit sensor 2

Detects discharged paper.

AR-BC260

PPD1

No. 1 paper transport sensor

Detects paper in front of the resist roller.

AR-BC260

PPD2

PS front sensor

Detects paper in front of PS.

AR-BC260

PSFM

Power UN cooling fan motor

Cools the power unit.

AR-BC260

PSHPS

Punch side registration home position 

AR-F13

PSM

PS motor

Drives the resist roller and controls ON/OFF.

AR-BC260

PUNCH

Punch home position

AR-F13

PWMFAN_ICU

Printer controller cooling fan motor

Cools the printer controller.

AR-BC260

RJHPS 

Alignment HP sensor R

AR-F13

SHPS 

Slide HP sensor

AR-F13

SLS 

Paper surface sensor

AR-F13

SM

Scanner motor

Drives the scanner unit.

AR-BC260

SPS

Staple sensor

Detects staple empty.

AR-F13

SS 

Staple cartridge sensor

Detects installation of a staple cartridge.

AR-F13

SSS Stapler 

safety 

switch

AR-F13

STHPS 

Stapler HP sensor

AR-F13

TCS Upper 

cover 

sensor

AR-F13

TES_C

Toner empty sensor (C) 

Detects toner empty (C).

AR-BC260

TES_K

Toner empty sensor (K)

Detects toner empty (K).

AR-BC260

TES_M

Toner empty sensor (M)

Detects toner empty (M).

AR-BC260

TES_Y

Toner empty sensor (Y)

Detects toner empty (Y).

AR-BC260

TFD2

Face-up paper exit tray full detection

Detects face-up paper exit tray full.

AR-BC260

TFD

Paper exit tray full detection 

Detects face-down paper exit tray full.

AR-BC260

THSD

Lower heat roller thermistor

Detects the temperature on the heat roller surface.

AR-BC260

THSU

Upper heat roller thermistor

Detects the temperature on the heat roller surface.

AR-BC260

TRC

PS front clutch

Transmits the paper feed motor power to the manual 
transport roller. (Controls ON/OFF.)

AR-BC260

ULS 

Lift upper limit sensor

AR-F13

VFMP

Exhaust fan motor 1

Exhaust and cools the fusing section.

AR-BC260

VFMS

Exhaust fan motor 2

Exhaust and cools the fusing section.

AR-BC260

W0

Document set sensor

Detects presence of a document.

AR-BC260 
(RSPF)

W1

Document width sensor 
(A4R, LTR, A5)

Detects the document width on the tray.

AR-BC260 
(RSPF)

W2

Document width sensor 
(B4, B5)

Detects the document width on the tray.

AR-BC260 
(RSPF)

W3

Document width sensor 
(WLTR, A5R, A4, LT)

Detects the document width on the tray.

AR-BC260 
(RSPF)

Signal name

Name

Function/Operation

Section

Summary of Contents for AR-BC260





















































































































































































































































































































Reviews:

No comments

Related manuals for AR-BC260

Datamax M-Class Mark II Maintenance Manual preview
M-Class Mark II
Brand: Datamax Pages: 94
Valentin DUOPRINT Operating Manual preview
DUOPRINT
Brand: Valentin Pages: 96
Oki ES2024 Software Installation Manual preview
ES2024
Brand: Oki Pages: 20
Xerox 4150S - WorkCentre B/W Laser Brochure & Specs preview
4150S - WorkCentre B/W Laser
Brand: Xerox Pages: 4
Tally XPRESS T9412i Network User'S Manual preview
XPRESS T9412i
Brand: Tally Pages: 76
Star Star NX-350 User Manual preview
Star NX-350
Brand: Star Pages: 82
Valentin Compa II Series Operating Manual preview
Compa II Series
Brand: Valentin Pages: 110
Oki PAGE 8w Lite Setup Manual preview
PAGE 8w Lite
Brand: Oki Pages: 18
Kyocera ECOSYS FS-C5350DN Service Manual preview
ECOSYS FS-C5350DN
Brand: Kyocera Pages: 178
Olivetti d-Color MF1600 Service Manual preview
d-Color MF1600
Brand: Olivetti Pages: 204
Ricoh Aficio 120 User Manual preview
Aficio 120
Brand: Ricoh Pages: 37
Xerox WORKCENTRE 7428 System Administrator Manual preview
WORKCENTRE 7428
Brand: Xerox Pages: 208
Copystar CS-C3225E Specifications preview
CS-C3225E
Brand: Copystar Pages: 1
Lexmark 26S0285 Specifications preview
26S0285
Brand: Lexmark Pages: 2
QMS qms-ps 800+ User Manual preview
qms-ps 800+
Brand: QMS Pages: 188
Sinfonia Technology DP-1045 Operation Manual preview
DP-1045
Brand: Sinfonia Technology Pages: 41
Canon MultiPASS C530 Quick Start Manual preview
MultiPASS C530
Brand: Canon Pages: 8
Canon MultiPASS F30 Reference Manual preview
MultiPASS F30
Brand: Canon Pages: 58

Brands by name

Popular brands

Load more brands