manualshive.com logo in svg

Sharp AR-BC260, Service Manual

Share
Download
Sharp AR-BC260 Service Manual Download Page 299

AR-BC260  PRINTER CONTROLLER SECTION  14 - 11

e. Initialize and/or store settings

You can restore the CONDITION SETTINGS and the key operator
program of the PRINTER SETTINGS to the factory default
settings.

You can also store the current configuration of these settings in
memory, and restore a stored configuration at a later time.

1) Restore factory defaults

This restores the CONDITION SETTINGS and the key operator
program of the PRINTER SETTINGS to the factory default
settings.

If you need a record of the settings prior to restoration of the
default settings, print the CUSTOM SETTINGS list and the key
operator program list.

This does not affect "Color adjustments" in the PRINTER
SETTINGS.

NOTE: After this program is set, exit the key operator program,

turn off the main switch, and then turn on the main switch
again after at least 3 seconds. The program will be effec-
tive at this time.

2) Store current configuration

This program is used to store the CONDITION SETTINGS and the
key operator program PRINTER SETTINGS in memory. The
stored settings will remain in memory even if the main switch is
turned off. To read the stored settings, use the following
[RESTORE CONFIGURATION] program.

This does not affect "Color adjustments" in the PRINTER
SETTINGS.

3) Restore configuration

This program is used to read the configuration that was stored
using the [STORE CURRENT CONFIGURATION] program and
restore it as the current configuration.

The currently set configuration will change to the configuration
read from memory.

B. Jumper Setting

Configuration for 3-pin jumper is shown as follows.

(1) Boot ROM Write Protect setting (JP1)

(2) Battery setting (JP7)

6. Operation

A. Printer driver setting and operation

(1) Document mode and image process

Boot ROM Write Protect

JP1

Factory Default

Normal

1-2 Short

Write Protect

2-3 Short

←

Battery

JP7

Factory Default

ON

1-2 Short

←

OFF

2-3 Short

JP1

VCCWB

BOOT

3

1

L 

⇔

 H

JP7

BATTERY

1

OFF 

⇔

 ON

3

Color Mode

Color

Gray Scale

Automatic

Original 
Type

Standard

 

 

 

 

 

 

 

Graphics

Photo

Drawing 
(Thin 
line)

Web 
Page

Custom

Summary of Contents for AR-BC260





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands