Sharp AR-BC260 Service Manual Download Page 208

Page: 208 / 308

AR-BC260 SIMULATION 9 - 70

(Sendable voice message)

(Items to be set)

(Adjustable items)

-12

Purpose

Operation test/check

Function
(Purpose)

Used to select a pattern and send it to the line and
the speaker at 300bps. (Level: soft SW setting)
(When the FAX is installed.)

Section

FAX

Item

Operation

Operation/
Procedure

1. Select the pattern to be sent.
2. Press the [EXECUTE] key.

NO SIGNAL

No signal (CML ON)

00000

Repetition of "00000"

11111

Repetition of "11111"

10101

Repetition of "10101"

11110

Repetition of "11110"

00001

Repetition of "00001"

-13

Purpose

Setting

Function
(Purpose)

Used to register a dial number for test used in SIM
66-14/15/16. (When the FAX is installed.)

Section

FAX

Item

Data

Registration

Operation/
Procedure

If a dial number is already registered, it is displayed
on "PRESENT: ."
1. Enter a dial number with the 10-key (displayed

on NEW:) and press [SET] key. The registered
number is displayed on "PRESENT:."

-14

Purpose

Adjustment

Function
(Purpose)

Used to adjust and check the make time of dial pulse
(10pps). (When the FAX is installed.)

Section

FAX

Item

Operation

Operation/
Procedure

1. Enter the make time to be set with the 10-key.
2. Press [OK] key to set.
3. Press [EXECUTE] key to send the pulse (dial set

with SIM 66-13).

Item

Set range

Default

Make time

0 – 15

11 (Europe)

6 (Australia, New Zealand)

-15

Purpose

Adjustment

Function
(Purpose)

Used to adjust and check the make time of the dial
pulse (20pps). (When the FAX is installed.)

Section

FAX

Item

Operation

Operation/
Procedure

1. Enter the make time to be set with the 10-key.
2. Press [OK] key to set.
3. Press [EXECUTE] key to send the pulse (dial set

with SIM 66-13).

Item

Set range

Default

Make time

0 – 15

-16

Purpose

Adjustment

Function
(Purpose)

Used to adjust and check the send level of DTFM
signal. (When the FAX is installed.)

Section

FAX

Item

Operation

Operation/
Procedure

1. Select an item to be adjusted with the scroll key.
2. Enter the set value with the 10-key.
3. Press [OK] key to set.
4. Press [EXECUTE] key to send pulses (dial set

with SIM 66-13) from the line at each setting of
the high group and the low group of the send
level.

Item

Set range

Default

Level (db)

0 – 15

Difference between the high and the
low groups

0 – 15

Summary of Contents for AR-BC260





















































































































































































































































































































Search results

Summary of Contents for AR-BC260

Reviews:

Related manuals for AR-BC260

Brands by name

Popular brands

Sharp AR-BC260, Service Manual

Search results

Summary of Contents for AR-BC260

Reviews:

Related manuals for AR-BC260

Brands by name

Popular brands