manualshive.com logo in svg

Sharp AR-BC260, Service Manual

Share
Download
Sharp AR-BC260 Service Manual Download Page 180

AR-BC260  SIMULATION  9 - 42

(Display items)

2. If the operation is normally completed, COMPLETE is 

displayed and the correction result becomes valid.

If the operation is not normally completed, ERROPR is highlighted 
and the detail of the trouble is displayed.

The detail of correction can be checked with SIM 44-9 and SIM 
44-12.

(Result/Detail messages list)

44

-4

Purpose

Setting

Function 
(Purpose)

Image forming section correction, image density 
sensor adjustment conditions setup

Section

Process (Photoconductor, development, transfer)

Item

Picture quality

Operation/
Procedure

1. Select the item to beg set by the scroll key.
2. Enter the set value with the 10-key, and press 

the [OK] key. (The entered value is set.)

Set all to the default values.

Display

Content

Min 

Value

Max 

Value

Default 

value

A

PCS_C TARGET

Color image density 
sensor adjustment target 
value

1

255

108

B

PCS_K TARGET

Black image density 
sensor adjustment target 
value

1

255

201

C

LED_C OUTPUT

Initial current level in 
color image density 
sensor adjustment

1

255

51

D

LED_K OUTPUT

Initial current level in 
black image density 
sensor adjustment

1

255

51

E

PCS ADJSTMENT 
LIMIT

Allowable error level in 
adjustments

1

255

2

F

BELT GROUND 
DIF

Error judgment level for 
the belt surface detection 
level difference

1

255

255

G

BIAS_CL 
STANDARD DIF

Set value (color) of the 
developing basis 
correction start voltage 
difference in high density 
image correction

0

255

50

H

BIAS_BK 
STANDARD DIF

Set value (black) of the 
developing basis 
correction start voltage 
difference in high density 
image correction

0

255

75

I

BIAS PATCH 
INTERVAL

Patch forming developing 
bias voltage interval 
(voltage difference) in 
high density image 
correction

1

255

50

J

Y_PAT TARGET 
ID

Base target density level 
(Y) in high density image 
correction

1

255

108

K

M_PAT TARGET 
ID

Base target density level 
(M) in high density image 
correction

1

255

125

L

C_PAT  TARGET 
ID

Base target density level 
(C) in high density image 
correction

1

255

109

M

K_PAT TARGET 
ID

Base target density level 
(K) in high density image 
correction

1

255

22

N

HV BK_GROUND 
LIMIT

Error judgment level for 
belt surface detection 
level difference 
(Allowable range of 
transfer belt surface 
detection level difference 
(mix. - min.) of black 
toner image patch 
position)

1

255

29

O

PCS_C MARKET 
TARGET

Adjustment target value 
(Color image density 
sensor) when adjusting 
the primary LED current 
value by using the 
calibration plate in 
SIM44-36.

1

255

110

P

PCS_C MARKET 
LED-REV

In SIM44-36, the toner 
patch density is read by 
three kinds of LED 
currents with the primary 
LED current adjustment 
value as the center value 
in order to obtain PCS C 
LED ADJ value. This is 
the deflection range of 
the current value in the 
above case. (Color image 
density sensor)

1

255

10

44

-6

Purpose

Operation test/check

Function 
(Purpose)

Used to forcibly execute the image forming section 
correction (high density process correction) (process 
correction).

Section

Process (Photoconductor, developing, transfer, 
cleaning)

Item

Operation

Operation/
Procedure

1. Press the [EXECUTE] key, and the image 

forming section correction is started.

Result display

Content

COMPLETE

Correction is normally completed.

ERROR

An error occurred during correction. 
(The previous correction result is 
maintained.)

COMPULSORY 
INTERRUPTION

Compulsory interruption

Error display

Content

COLOR_SENSOR_
ADJUSTMENT_ERROR

Color image density sensor 
adjustment error

BLACK_GAIN_
ADJUSTMENT_ERROR

Black image density sensor 
gain adjustment error

BLACK_SENSOR_
ADJUSTMENT_ERROR

Black image density sensor 
adjustment error

BLACK_PROCON_ERROR

High-density image density 
correction (process 
correction) error (K)

CYAN_PROCON_ERROR

High-density image density 
correction (process 
correction) error (C)

MAGENTA_PROCON_ERROR

High-density image density 
correction (process 
correction) error (M)

YELLOW_PROCON_ERROR

High-density image density 
correction (process 
correction) error (Y)

CONNECTION_ERROR

Sensor-PCU PWB 
communication trouble

Display

Content

Min 

Value

Max 

Value

Default 

value

Summary of Contents for AR-BC260





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands