Sharp AR-BC260 Service Manual Download Page 286

Page: 286 / 308

AR-BC260 ELECTRIC DIAGRAM 13 - 18

3. Signal list

Signal name

Name

Function/Operation

Section

APAM

Alignment motor

Aligns paper in ADU.

AR-D19N

APHPS

Alignment plate home position
detection

Detects the alignment plate in ADU.

AR-D19N

APPD1

ADU transport sensor 1

Detects paper transport in ADU.

AR-D19N

APPD2

ADU transport sensor 2

Detects paper transport in ADU.

AR-D19N

ARHPS

Bundle roller HP sensor

AR-F13

Alignment tray sensor

AR-F13

ATM

ADU transport motor

Drives the paper transport section in ADU.

AR-D19N

ATRC

ADU transport clutch

Controls ON/OFF of the transport roller in ADU.

AR-D19N

BDD

Door open detection 1

Detects upper door open.

AR-RB1

BDD2

Door open detection 2

Detects left door open.

AR-RB1

BES

Tray paper sensor

AR-F13

BGSOL

Gate solenoid

Switches straight or reverse paper exit.

AR-RB1

BIM

Paper entry motor

Transports paper in the paper entry section.

AR-RB1

BLUD

Belt lift-up upper limit detection

Detects if the transfer belt is lifted up or down.

AR-BC260

BLUM

Belt lift-up motor

Lifts the transfer belt unit.

AR-BC260

BPFD

Full sensor

Detects paper full on the tray.

AR-RB1

BPOD

Paper exit sensor

Detects paper exit.

AR-RB1

BPPD1

Transport sensor 1

Detects paper transport.

AR-RB1

BPPD2

Transport sensor 2

Detects paper transport.

AR-RB1

BPRD

Reverse section sensor

Detects paper presence in the reverse section.

AR-RB1

BRM

Upper reverse motor

Transports paper in the upper section.

AR-RB1

BTM

Transport belt motor

Drives the transfer belt.

AR-BC260

BTM

Lower reverse motor

Transports paper in the lower section.

AR-RB1

BTNF

Belt waste toner detection

Detects belt waste toner full.

AR-BC260

C1SS1

1 cassette paper size detection 1

Detects the paper size which is set by the paper size set
block.

AR-BC260

C1SS2

1 cassette paper size detection 2

Detects the paper size which is set by the paper size set
block.

AR-BC260

C1SS3

1 cassette paper size detection 3

Detects the paper size which is set by the paper size set
block.

AR-BC260

C1SS4

1 cassette paper size detection 4

Detects the paper size which is set by the paper size set
block.

AR-BC260

CALS

Calibration plate open/close solenoid

Switches image density sensors.

AR-BC260

COVER

Open/close sensor

Detects open/close of the paper feed unit.

AR-BC260
(RSPF)

COVER OPEN

Book sensor

Detects floating of the RSPF.

AR-BC260
(RSPF)

CPFC1

Paper feed clutch

Transmits the paper feed motor power to each transport
roller. (Controls ON/OFF.)

AR-BC260

DCSPSx

Paper remaining quantity sensor

Detects the remaining quantity of paper.

AR-D17N/
AR-D18N

DCSSx

Paper size sensor

Detects the paper size.

AR-D17N/
AR-D18N/
AR-D19N

DDOPD

Door open sensor

Detects opening of the right door.

AR-D17N/
AR-D18N

DHSW

Dehumidifier heater switch

Turns ON/OFF the power line of the dehumidifier heaters
provided in the scanner (reading) section and the paper feed
section.

AR-BC260

DLMx

Lift motor

Drives the lift plate.

AR-D17N/
AR-D18N/
AR-D19N

DLUDx

Paper upper limit sensor

Detects the paper upper limit position.

AR-D17N/
AR-D18N/
AR-D19N

Paper feed drive motor

Drives the paper feed section and the paper transport
section.

AR-D17N/
AR-D18N/
AR-D19N

DM_C

Drum motor (C)

Drives the Cyan photoconductor unit.

AR-BC260

DM_K

Drum motor (K)

Drives the Black photoconductor unit.

AR-BC260

DM_M

Drum motor (M)

Drives the Magenta photoconductor unit.

AR-BC260

DM_Y

Drum motor (Y)

Drives the Yellow photoconductor unit.

AR-BC260

Summary of Contents for AR-BC260





















































































































































































































































































































Search results

Summary of Contents for AR-BC260

Reviews:

Related manuals for AR-BC260

Brands by name

Popular brands

Sharp AR-BC260, Service Manual

Search results

Summary of Contents for AR-BC260

Reviews:

Related manuals for AR-BC260

Brands by name

Popular brands