Home
/
Sharp
/
AR-BC260
/
Service Manual

Sharp AR-BC260, Service Manual

Share

Page: 154 / 308

Sharp AR-BC260 Service Manual Download Page 154

AR-BC260 SIMULATION 9 - 16

When the [TRC ON] key or the [TRC OFF] key is pressed, the
TRC clutch is turned ON or OFF.

If the response of monitoring TRC ON/OFF is made, DESK
SENSOR TRC ON/OFF is displayed.

↓

6sec

The selected heater lamp repeats ON/OFF in the frequency of
500msec for 10sec. (The [EXECUTE] key is highlighted.) Then the
[EXECUTE] key returns to the normal display. When the
[EXECUTE] key is pressed during ON/OFF operation of the heater
lamp, the heater lamp is turned OFF and the [EXECUTE] key
returns to the normal display.

After 10 sec, the scanner lamp is turned OFF. At that time, the
[EXECUTE] key returns to the normal display.

4

-5

Purpose

Operation test/check

Function
(Purpose)

Used to check the operations of the clutch TRC and
the monitor.

/

Section

Paper feed

Item

Operation

Operation/
Procedure

1. Press the [TRC ON] key. (The load operates.)
2. Press the [TRC OFF] key to terminate checking.

5

5

-1

Purpose

Operation test/check

Function
(Purpose)

Used to check the operations of the display lamp
(LED)/LCD on the operation panel and the control
circuits.

Section

Operation (Display, procedure)

Item

Operation

Operation/
Procedure

The LCD shows the following message. (The
contrast changes in the sequence of Current level

→

MAX

→

MIN

→

Current level

→

MAX

→

MIN in every

2sec.) During that period, each LED is lighted for
12sec.

5

-2

Purpose

Operation test/check

Function
(Purpose)

Used to check the operations of the heater lamp and
its control circuit.

/

Section

Fusing

Item

Operation

Operation/
Procedure

1. Select the lamp to be checked with the key.
2. Press the [EXECUTE] key.

HL1 (UPPER)

Upper heater lamp

HL2 (LOWER)

Lower heater lamp

HL1&2 (UPPER & LOWER)

Upper/lower fusing heater lamp

5

-3

Purpose

Operation test/check

Function
(Purpose)

Used to check the operations of the scanner lamp
and its control circuit.

/

Section

Scanner (reading)

Item

Operation

Operation/
Procedure

When the [EXECUTE] key is pressed, the scanner
lamp is lighted for 10 sec. While the scanner lamp is
lighted, the [EXECUTE] key is highlighted. If the
[EXECUTE] key is pressed under this state, the
lamp is turned OFF.

«
...
152
153
154
155
156
...
»

Summary of Contents for AR-BC260





















































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands