manualshive.com logo in svg

Sharp AR-BC260, Service Manual

Share
Download
Sharp AR-BC260 Service Manual Download Page 213

AR-BC260  SIMULATION  9 - 75

2. Use "fcopy" command on the PC side to download the 

firmware file. 

When the firmware data are normally downloaded and written into
the Flash ROM, "COMPLETE" is displayed. 

In case of an error, the following message is displayed. 

∗

When the Flash ROM kind is improper:
 "ROM KIND ERROR" is displayed.

∗

When an error occurs during initializing the Flash ROM:
"FLASH ERROR" is displayed.

∗

When an error occurs during verifying:
"UPDATE ERROR" is displayed.

1. Press [EXECUTE] key. (A3 or 11" x 17" paper is automatically 

selected.)
The color patch image (adjustment pattern) is printed out.

2. Set the color patch image (adjustment pattern) printed in 

procedure 1) on the document table.

3. Press [FACTORY] key on the operation panel, and press 

[EXECUTE] key.
The printer color balance adjustment (step 1) is automatically 
performed and the color balance check patch image is printed 
out.

4. Press [REPEAT] key.
5. Press the [EXECUTE] key. 

The color patch image (adjustment pattern) is printed out.

67

-11

Purpose

Setting

Function 
(Purpose)

Used to set the printer parallel I/F SELECT IN 
signal.

Section

Printer

Item

Operation

Operation/
Procedure

Enter the set value with the 10-key, and press the 
[OK] key.
When a trouble occurs in communication between 
PC and the printer by use of the printer parallel I/F, 
change the setup content of this simulation.

Display

Content

Set range

Default

A

SELECT-IN 
(0:OFF 1:ON)

Centro I/F SELECT IN 
signal YES/NO setting

0 –  1

1

67

-14

Purpose

Version up

Function 
(Purpose)

Used to perform version up of the firmware. (Printer)

Section

Firmware (Printer)

Item

Operation

Operation/
Procedure

1. When the machine enters the simulation mode, it 

enters the printer firmware version up mode at 
the same time.

67

-17

Purpose

Data clear

Function 
(Purpose)

Used to clear NVRAM. (Printer)

Section

Printer

Item

Others

Operation/
Procedure

1. Press the [EXECUTE] key. 

The confirmation message to clear is displayed. 

2. Select YES/NO to clear the NVRAM.

YES: Clear
NO: Not clear

When the printer NVRAM is normally cleared, 
"COMPLETE" is displayed. In case of an error, 
"ERROR" is displayed.

67

-18

Purpose

Data clear

Function 
(Purpose)

Used to clear the Flash data. (Printer)

Section

Printer

Item

Others

Operation/
Procedure

1. Press the [EXECUTE] key.

The confirmation message to clear the Flash 
data is displayed. 

2. Select YES/NO to clear the Flash data.

YES: Clear
NO: Not clear

When the printer Flash data are normally cleared, 
"COMPLETE" is displayed. In case of an error, 
"ERROR" is displayed.

67

-24

Purpose

Adjustment

Function 
(Purpose)

Used to adjust half-tone density of the printer engine 
automatically.

Operation/
Procedure

1. Select a color to be set. 
2. Select an item to be set.

Summary of Contents for AR-BC260





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands