Sharp AR-BC260, Service Manual

Page: 195 / 308

AR-BC260 SIMULATION 9 - 57
2. Enter the adjustment value of the selected point with the 10-
key, and press the [OK] key. (The entered adjustment value is
set. The [EXECUTE] key or the scroll key can be used instead
of the [OK] key in the above procedure.)
3. Select the paper feed mode.
4. Press the [EXECUTE] key.
The test pattern corresponding to the entered adjustment value is
printed.
When the adjustment value of item A (DEN-C) is decreased by 1,
the print start position in the sub scanning direction shifts
0.125mm toward the paper lead edge.
When the adjustment value of item B (DEN-B) is decreased by 1,
the print start position in the sub scanning direction shifts
0.125mm toward the paper rear edge.
(Descriptions on Set values)
(Descriptions on Set values)
2. Enter the adjustment value of the selected point with the 10-
key, and press the [OK] key. (The entered adjustment value is
set. The [EXECUTE] key or the scroll key can be used instead
of the [OK] key in the above procedure.)
3. Press the [EXECUTE] key. The test pattern corresponding to
the entered adjustment value is printed.
50 -5
Purpose Adjustment
Function
(Purpose) Used to adjust the image position and print area in
the sub scanning direction. (Print engine section)
Section ICU/Printer
Item Picture quality
Operation/
Procedure 1. Select the adjustment mode (DEN-B/DEN-C)
with the scroll key.
Display Content
Min.
Value
Max.
Value
Default
A DEN-C Sub scanning print lead
edge adjustment 1 99 40
B DEN-B Sub scanning print area
adjustment 1 99 40
C MULTI
COUNT
Print quantity 1 999 1
D PAPER Paper feed tray selection
(MFT, CS1, CS2, CS3,
CS4, LCC) 1 6 2 (CS1)
E EXIT
TRAY
Paper exit tray selection
(R, S) 1 2 1 (R)
F
DUPLEX Duplex print selection
(NO, YES)
1 2 1 (NO)
50 -6
+
Purpose Adjustment
Function
(Purpose) Used to adjust the document lead edge and image
loss quantity of the document feeder unit.
Section Automatic document feeder
Operation/
Procedure 1. Select an adjustment item with the scroll key.
2. Enter the adjustment value of the item selected
with the scroll key, and press [OK] key. (The
adjustment value is set. It is set also when the
scroll key is pressed.)
Display Content
Min.
Value
Max.
Value
Default
A SIDE1 Document feeder unit
front surface scan lead
edge adjustment 1 99 50
B SIDE2 Document feeder unit
back surface scan lead
edge adjustment 1 99 50
C LEAD
IMAGE
LOSS
RSPF lead edge image
loss quantity adjustment 0 99 40
D REAR
IMAGE
LOSS
RSPF rear edge image
loss quantity adjustment 0 99 0
50 -10
+
Purpose Adjustment
Function
(Purpose) Used to adjust the print image center position.
(Adjustment is performed in each paper feed
position separately.)
Section Image process (ICU)
Item Picture quality Image position
Operation/
Procedure 1. Select the adjustment mode (DEN-B/DEN-C)
with the scroll key.
Display Content Set range Default
A MFT Print off-center adjustment
value (Manual paper feed) 1 – 99 50
B CS1 Print off-center adjustment
value (1 cassette) 1 – 99 50
C CS2 Print off-center adjustment
value (2 cassette) 1 – 99 50
D CS3 Print off-center adjustment
value (3 cassette) 1 – 99 50
E CS4 Print off-center adjustment
value (4 cassette) 1 – 99 50
F LCC Print off-center adjustment
value (LCC) 1 – 99 50
G ADU Print off-center adjustment
value (ADU) 1 – 99 50
H MULTI
COUNT
Print quantity 1 – 999 1
I PAPER Paper feed tray selection
(MFT, CS1, CS2, CS3,
CS4, LCC) 1 – 6 2 (CS1)
J EXIT TRAY Paper exit tray selection
(R, S)
1 or 2 1
K DUPLEX Duplex print selection
(NO, YES) 1 or 2 1