manualshive.com logo in svg

Sharp AR-BC260, Service Manual

The Sharp AR-BC260 is a versatile printer that offers high-quality output. To easily set it up and begin printing, make sure to download the free Installation Manual from our website. This comprehensive manual provides step-by-step instructions and is available for instant download at manualshive.com.

Share
Download
background image

AR-BC260  SIMULATION  9 - 56

A. Document lead edge reference position --- (RRC-A) This set 

value is used to adjust timing from when the document 
scanning is started to when the image lead edge signal
(Set range: 1 – 80) (Default value: 50)

B. Paper lead edge position --- (RRC-B) Used to adjust timing of 

turning on the resist roller after receiving the resist signal 
(LD_START).

(Set range: 1 – 99) (Default value: 50)

C. Lead edge void area --- (DEN-A) Used to specify the void area 

at the lead edge of the document. 
(Set range: 1 – 99) (Default value: 40)

D. Rear edge void area --- (DEN-B) Used to specify the void area 

at the rear edge of the document. 
(Set range: 1 – 99) (Default value: 40)

E. Lead edge image loss --- (IMAGE LOSS) Used to specify the 

image loss. 
(Set range: 0 – 99) (Default value: 40)

This simulation is used to perform the lead edge adjustment by 
directly entering the lead edge shift in 400% copy.

(Default values)

A. Document lead edge reference position --- (L1) 240
B. Paper lead edge position --- (L2) 40
C. Lead edge void area --- (DEN-A) 40
D. Rear edge void area --- (DEN-B) 40
E. IMAGE LOSS --- 40

49

-2

Purpose

Version up

Function 
(Purpose)

Used to set the data communication speed in 
version up of the machine firmware.

Section

Firmware

Item

Operation

Operation/
Procedure

Press the key corresponding to the data 
communication speed on the PC side.
Unit (bps: bit per second)

49

-10

Purpose

Version up

Function 
(Purpose)

Used for firmware version up (Desk unit).

Section

Firmware (Desk unit)

Item

Operation

Operation/
Procedure

1. Press the [EXECUTE] key to enter the Flash 

ROM writing mode.

2. Start the download program on the PC side and 

perform Flash ROM writing.

50

50

-1

Purpose

Adjustment

Function 
(Purpose)

Used to adjust the copy image position and the void 
area (image loss) on print paper in the copy mode. 
(The similar adjustment can be made also by SIM 
50-2 (Simple method).)

Item

Picture quality

Image position

Operation/
Procedure

1. Select the adjustment item with the scroll key.
2. Enter the adjustment value with the 10-key.
3. Press the [OK] key.

Display

Content

Min. 

Value

Max. 

Value

Default

A RRC-A

Document lead edge 
reference position

1

80

50

B RRC-B

Paper lead edge 
position

1

99

50

C DEN-A

Lead edge void area

1

99

40

D DEN-B

Rear edge void area

1

99

40

E IMAGE LOSS Lead edge image 

loss

0

99

40

50

-2

Purpose

Adjustment

Function 
(Purpose)

Used to adjust the copy image position and the void 
area (image loss) on print paper in the copy mode. 
(Simple method)
(The same content of SIM 50-1. However this 
simulation is easier to perform.)

Item

Picture quality

Image position

Operation/
Procedure

1. Select the adjustment item with the scroll key. 
2. Enter the adjustment value with the 10-key.
3. Press the [OK] key.

Display

Content

Min. 

Value

Max. 

Value

Default

A L1

Document lead edge 
reference position

1

999

240

B L2

Paper lead edge 
position

1

999

40

C DEN-A

Lead edge void area

1

99

40

D DEN-B

Rear edge void area

1

99

40

E IMAGE LOSS Document lead edge 

image loss 
adjustment value

1

99

40

Summary of Contents for AR-BC260





















































































































































































































































































































Reviews:

No comments

Related manuals for AR-BC260

Oki 10i Read Me First preview
10i
Brand: Oki Pages: 16
Olivetti d-COLOR MF254 Replacement Procedure preview
d-COLOR MF254
Brand: Olivetti Pages: 2
Olivetti d-COLOR MF3300 Operations preview
d-COLOR MF3300
Brand: Olivetti Pages: 109
Olivetti d-COLOR MF3300 User Manual preview
d-COLOR MF3300
Brand: Olivetti Pages: 111
Olivetti d-Color MF1600 Setup Manual preview
d-Color MF1600
Brand: Olivetti Pages: 8
Oki T410 Safety Information Manual preview
T410
Brand: Oki Pages: 24
NEC SuperScript 610 User Manual preview
SuperScript 610
Brand: NEC Pages: 105
Oki C710cdtn User Manual preview
C710cdtn
Brand: Oki Pages: 72
Konica Minolta Magicolor 7440 Installation Manual preview
Magicolor 7440
Brand: Konica Minolta Pages: 15
Muratec MFX-3550 User Manual preview
MFX-3550
Brand: Muratec Pages: 213
SII DPU-30 Technical Reference preview
DPU-30
Brand: SII Pages: 85
Ricoh PRSPC342DN1 User Manual preview
PRSPC342DN1
Brand: Ricoh Pages: 120
Kyocera FS-1041 Quick Installation Manual preview
FS-1041
Brand: Kyocera Pages: 16
Xerox 1235/DX - Phaser Color Laser Printer Advanced Features And Troubleshooting Manual preview
1235/DX - Phaser Color Laser Printer
Brand: Xerox Pages: 144
DURACARD ID 300 User Manual preview
ID 300
Brand: DURACARD Pages: 31
Sam4s GIANT-100 User Manual preview
GIANT-100
Brand: Sam4s Pages: 24
Carl Valentin SPE series Operating Manual preview
SPE series
Brand: Carl Valentin Pages: 106
Ricoh Aficio GX7000 Setup And Print Manual preview
Aficio GX7000
Brand: Ricoh Pages: 5

Brands by name

Popular brands

Load more brands