Sharp AR-235 Operation Manual Download | Manualshive

Page: 18 / 158

background image

16

GE

T

T

IN

G

S
T

ARTE

D

POWER ON AND OFF

The power switch is located on the left side of the copier.

Power on

Turn the power switch to the "ON" position.

●

When the power switch is turned to the "ON" position, the message "System check." will appear in the
message display and warm-up will start. During warm-up, you can select your desired job settings
and then by pressing the START (

) key, your job will commence when the copier comes to "Ready

to copy.". Once the copier has finished warming up, the message display will change to "Ready to
copy.", and the START (

) key indicator will light up, indicating that copying is possible.

●

If the copier has been programmed in the auditing mode, the message "Enter your account number."
will appear after warming up. Once a valid account number has been entered, the message display
will change to "Ready to copy." and copying will be possible. See page 20.

Power off

When the copier is not used for a long time, be sure to turn it off.

Ensure that the machine is not operating and then turn the power switch to the "OFF" position.

If the power switch is turned off while the machine is operating, a misfeed may occur. Also the job that
was in progress will be totally cancelled.

Power on

Power off

00EX.book 16 ページ２００１年５月２５日金曜日午前１０時４９分

«
...
16
17
18
19
20
...
»

Summary of Contents for AR-235































































































































































Reviews:

No comments

Related manuals for AR-235

Brand: Oce Pages: 389

Brand: Canon Pages: 362

Brand: Canon Pages: 424

Brand: Canon Pages: 20

Brand: Avision Pages: 51

Brand: Avision Pages: 65

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands