Sharp AR-235 Operation Manual Download | Manualshive

Page: 34 / 158

background image

REDUCTION/ENLARGEMENT/ZOOM

32

MA

KING COP

IE

S

3

Press the AUTO IMAGE key.

●

The copy ratio will be automatically set.

●

If the original and the selected copy paper are not in the same orientation, the image will
be automatically rotated to match the copy paper. However, if enlargement is selected for
copying onto a paper size larger than A4 (8-1/2" x 11"), the image will not be rotated. In
this case a message indicating "Image edge loss" will appear.

★

KEY OPERATOR

Rotation of the image can be disabled using a key operator program.

See page 128.

●

If the message "Image edge loss" is displayed, part of the original image may not be
copied.

4

Enter the number of copies and press the START (

) key.

●

To cancel the automatic reduction/enlargement mode, press the AUTO IMAGE key
again.

●

When copying from an optional SPF or RSPF, the automatic reduction/enlargement
feature will be effective only for the current copy run.

00EX.book 32 ページ２００１年５月２５日金曜日午前１０時４９分

«
...
32
33
34
35
36
...
»

Summary of Contents for AR-235































































































































































Reviews:

No comments

Related manuals for AR-235

Brand: Olivetti Pages: 753

Brand: Olivetti Pages: 297

Brand: Olivetti Pages: 242

Brand: Canon Pages: 62

Brand: RealSYS Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands